Installation Instructions

ManualsBrandsToro ManualsRiding ProductsMotor Mount Kit, Greensmaster 3300 or 3320 TriFlex Traction Unit

FormNo.3447-604RevA

MotorMountKit

Greensmaster

3300or3320TriFlex

TractionUnit

ModelNo.145-0057

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removeanexistingmotormount.

Motoradapter1

Motormount1

Hex-headbolt(5/16inch)

Nut(5/16inch)

Hex-headbolt(3/8inch)

Nut(3/8inch)

Hex-headbolt(1/4inch)

Nut(1/4inch)

Cylinderspacer

Spacer

Installamotormount.

Motoradapter1

Motormount1

Hex-headbolt(5/16inch)

Nut(5/16inch)

Hex-headbolt(3/8inch)

Nut(3/8inch)

Hex-headbolt(1/4inch)

Nut(1/4inch)

Cylinderspacer

Spacer

Removeandinstalltheremainingmotor

mount.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3447-604*

Summary of content (4 pages)

PAGE 1
Form No. 3447-604 Rev A Motor Mount Kit Greensmaster® 3300 or 3320 TriFlex® Traction Unit Model No. 145-0057 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty. No parts required – Prepare the machine. No parts required – Remove an existing motor mount.
PAGE 2
Removing an Existing Motor Mount No Parts Required Procedure g361994 Figure 2 Important: Remove and install a single motor mount at a time (e.g., remove and install the left motor mount, then remove and install the right motor mount). If both mounts are simultaneously removed, then installed, the engine frame assembly becomes unstable. 1. 1. Bolt 4. Flat spacer 2. Engine frame 5. Nut 3. Cylinder spacer 3. Place a jack under the engine (Figure 1).
PAGE 3
Installing a Motor Mount Parts needed for this procedure: 1 Motor adapter 1 Motor mount 2 Hex-head bolt (5/16 inch) 2 Nut (5/16 inch) 1 Hex-head bolt (3/8 inch) 1 Nut (3/8 inch) 4 Hex-head bolt (1/4 inch) 4 Nut (1/4 inch) 1 Cylinder spacer 1 Spacer g360968 Figure 5 1. Hex-head bolt (5/16 inch) 3. Nut (5/16 inch) 2. Motor mount 3. Use 1 hex-head bolt (3/8 inch), 1 cylinder spacers, 1 spacer, and 1 nut (3/8 inch) to secure the engine frame to the motor mount (Figure 6).
PAGE 4
Removing and Installing the Remaining Motor Mount Parts needed for this procedure: 1 Motor adapter 1 Motor mount 2 Hex-head bolt (5/16 inch) 2 Nut (5/16 inch) 1 Hex-head bolt (3/8 inch) 1 Nut (3/8 inch) 4 Hex-head bolt (1/4 inch) 4 Nut (1/4 inch) 1 Cylinder spacer 1 Spacer Procedure 1. Remove and install the remaining motor mount; refer to the steps listed in 2 Removing an Existing Motor Mount (page 1) and 3 Installing a Motor Mount (page 2). 2. Remove the jack from the engine.