FORM NO. 3313-314, Rev. A MODEL NO MODEL No. 18875 OPERATOR'S thru & UP MANUAL FINGERTIP START k 21" (0.53 SIDE DISCHARGE A\ SAFETY INSTRUCTIONS This mower “meets or exceeds CPS blade safety requirements for walk behind rotary mowers,” and the specifications of the American National Standards Institute, However, improper use or maintenance by the operator or owner can result in injury.
A\ SAFETY INSTRUCTIONS 20. Before mower is cleaned, inspected, serviced or adjusted, stop engine and disconnect high tension wire from spark plug. Keep wire away from plug to prevent accidental starting 21. To assure the mower is in safe operating condition, frequently check and k Keep all nuts, bolts and screws tight. Assure blade bolt is tightened to proper specification 22. To reduce fire hazard, keep engine free of excessive grease, grass, leaves and accumulations of dirt. 23.
SET-UP INSTRUCTIONS INSTALL HANDLES AND STARTER ROPE 1. LOWER HANDLES (Fig. 1) — Push ends of handle together and install on pivot pins. Move handle ang latches backward unfit handier studs snap into center hole. Push hair pin cotters through holes in pivot pins. Figure 1 2. UPPER HANDLE (Fig. 2) — Secure upper and dower handles in place with handier screws. and flange nuts. Control cables must be in front of lower handier cross member. Secure control cables in position with cable clip, 3.
BEFORE OPERATING FILL CRANKCASE WITH OIL Initially, crankcase must be filled with 21 ounces {0.621 1} of SAE 30 or 10W30 oil. Use any high quality detergent oil having the American Petroleum Institute — APt — “service classification” Before each use, assure off level is between "FULL” and “"ADD" marks on dipstick. Add oil if level is low, 1. Position mower on level surface and clean around oil dipstick, 2. Remove dipstick by rotating cap counterclockwise 1/4 turn. 3.
OPERATING INSTRUCTIONS 2-IN-1 MOWING VERSATILITY SIDE DISCHARGE — In summer, disperse clippings to the side when grass grows slower and is drier. SIDE BAG — Optional side bag kit {Fig. 5} jets you bag lush grass in spring ta help keep your fawn free of thatch forming clippings. In the fail, bag leaves while you mow to eliminate the hand-blistering raking job OPTIONAL 5(0€ BAGGING KIT Figure 8 STARTING, STOPPING, SELF-PROPELLING 1. CONTROLS (Fig.
OPERATING INSTRUCTIONS Figure 8 1. Geoengineering pull wire off spark plug. 2. For easier adjustment, lift housing up so wheel is off ground. Squeeze adjusting ever toward wheel (Fig. 9) and move them to desired setting. Assure pin on adjusting lever engages notch in housing. Adjust all wheels to the same setting. Note: Front wheels can be adjusted to cinch, Use this setting with 1-inch rear wheel setting.
MAINTENANCE A CAUTION Putt high tension wire off spark plug before performing adjustments or maintenance. SERVICING AiR CLEANER Normally, clean air cleaner after every 25 aerating hours. More frequent cleaning is required when mower is operated in dusty or dirty conditions. 1. Stop engine and pull wire off spark plug. 2. Lift off air cleaner cover and clean thoroughly {Fig. 10} 3. i top of fem element is dirty, remove it from air cleaner body (Fig. 10}. Clean thoroughly. AIR CLEANER COVER = FOAM.
MAINTENANCE Figure 12 CHANGING CRANKCASE OIL Change oil after the first 2 operating hours and tater every 25 hours thereafter. Since warm oit drains better and carries more contaminants than cold oil, run engine for a minute or so before draining oil. 1. Stop engine and pull wire off spark plug. 2. Remove grass bag. Drain gasoline from fuel tank: refer to Draining Gasoline, page 7 3. Remove dipstick. Tip mower forward and employ ali oil into drain pan (Fig. 13).
MAINTENANCE FLAT PART All OF BLADE Sally, WEAR e At . 10T " FORMED Figure 15 A CAUTION i blade is allowed {6 wear, a soot may torn near the sail, Eventually a piece of blade may break off resulting in serious injury to yourself or a bystander. 5. REMOVING BLADE — Grasp end of blade using as rag or thickly padded glove. Remove blade obit. lock washer and blade (Fig. 14). Note: For optimum performance, install new blade before cutting season begins.
MAINTENANCE IMPORTANT: Low oii level may indicate leak where axle goes through both sides of transmission case. Transmission case should be inspected by an Authorized TOR Service Dealer. PROPER LEVELER Figure 18 3. ADDING GEAR Oil. — Slowly add #80 gear ot that has a LG-5 or LG-8 rating. Stop when oil posses out of hole in gear case. and quickly install plastic plug. DO NOT OVER TIGHTEN PLASTIC PLUG BECAUSE THREADS MAY STRIP.
MAINTENANCE 3. Remove spark plug and pour 2 teaspoons parts of the engine. shrouding and top of of 10W30 ¢il into hot in cylinder. Pull starter mower housing. rope slowly to coat inside of cylinder. install 8 Clean air cleaner: refer to Servicing Air spark plug and tighten to 18 phi-lb (244 N'm). Cleaner, page 7. DO NOT INSTALL WIRE ON SPARK PLUG. 9. Lubricate the wheels: refer to Lubrication, 4. Clean underside of housing: refer to Clean page 9 ing Mower Housing. page 8. 10.
The Toto Promise A Twe Year Limited Warranty On Al Gasoline Powered Consumer Products The Toto Company promises to repair these TOR Products if defective in materialism or workmanship, The flowing time periods from the date of purchase apply: Residential Product Residential Products Used Commercially 2 Years 45 Days The cows of parts and labor are included, huy the customer pays the transportation casts.