Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 19053

Printed in the USA

 2001 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Electric Winch Kit

Twister Utility Vehicle

Model No. 19053

Form No. 3326-468 Rev A

Installation Instructions

Installation

Preparing the Vehicle

1. Position the machine on a level surface. Set the parking

brake, stop the engine, and remove the key.

If you leave the key in the ignition switch, someone

could accidently start the engine and seriously

injure you or other bystanders.

Remove the key from the ignition switch before

you do any maintenance.

Caution

2. Remove the hood from the vehicle by removing the 2

screws in the top of the hood, the 2 bolts on each fender,

and the 4 bolts from the bottom of the hood.

3. Remove the cargo box by removing the prop rod and

one of the brackets on the back of the frame. Lift up on

the box and slide it off of the frame.

4. Remove the fuse box cover.

5. Remove the rubber boot from the positive (+) battery

cable and disconnect the battery cable from the battery.

Attaching the Solenoid Assembly

1. Locate, mark, and drill 2 holes (0.30 in. [7.6 mm]

diameter) in the rear frame as shown in Figure 1.

2. Attach the solenoid assembly to the inside of the rear

frame with 2 bolts (1/4 x 3/4 in.), spacers, and flange

nuts (1/4 in.) (Fig. 1).

m–5666

6 in.

(15.24 cm)

13 in.

(33 cm)

1-3/8 in.

(3.5 cm)

Figure 1

1. 0.30 in. (7.6 mm)

diameter hole

2. Solenoid assembly

3. Bolt, 1/4 x 3/4 in.

4. Spacer

5. Flange nut, 1/4 in.

Routing the Wire Harness

1. Remove the 2 small bolts securing the panels to the

front of the operator’s compartment (Fig. 2).

2. Using a screw driver or similar tool, pry apart the

overlap in the harness opening in the vehicle

compartment to allow greater access.

Note: Make sure that the vehicle is in a temperature above

68 degrees so that the opening in not stiff when prying.

Figure 2

1. Mounting bolts

2. Harness opening

3. Existing harness

Summary of content (4 pages)

PAGE 1
Form No. 3326-468 Rev A Electric Winch Kit Twister Utility Vehicle Model No. 19053 Installation Instructions Installation 6 in. (15.24 cm) 1 Preparing the Vehicle 13 in. (33 cm) 1. Position the machine on a level surface. Set the parking brake, stop the engine, and remove the key. Caution 1-3/8 in. (3.5 cm) If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders.
PAGE 2
3. Carefully tape the 3 loose control plug terminals and wire to the harness to ease harness routing. Tape the terminals to the end of the harness, away from the solemoid assembly. 6. Connect the remote control to the control plug. 4. Route the harness through the hole in the front of the rear frame. 1. Remove the nut securing the positive battery cable to the starter solenoid (Fig. 4). 5.
PAGE 3
7. Connect the front plug on the wire harness to the winch plug. 3 4 12 7 1 8. Install the cargo box, prop rod, and hood. 11 8 Connecting the Winch to the Rear of the Vehicle If you already have a rear receiver hitch, the winch can be attached to the rear of the vehicle. 5 1. Loop the front end of the wire harness back into the frame tube. 2 2. Follow steps 5–6 in Attaching the Winch to the Front of the Vehicle, page 2. 6 11 9 3. Connect the rear plug on the wire harness to the winch plug.
PAGE 4