TOR General 3 l Maintenance and Upkeep 15 2 Safety 5 A Spare Parts and Troubleshooting 20 @% Assembly and Start-up 7 \ Hints on Tending the Lawn 23 L ¥gen recitative Operation 11 @ 1998 by TOR Company
TOR 1 General 11 introduction 1.2 Regulation on Time Limits for the Operation of Lawn Mowers. 1.3 Technical Data 1.1 Introduction The TOR lawn mower has been designed according to the latest technical and physiological aspects with due regard to the safety regulations in tore. With its special equipment the Recycler® -Mower can cut up grass and leaves several times.
Manufacturer Product Name Serial Number Model Number Noise information Signature, Title, Date GB EC Declaration of Conformity 1o Dir actives y Certificate of Conformity (i 88/392, 91/368, 93/44, 93/68, 89/336, 73/23 (EN60335) Conforms to the Specifications of Directive 84/538/EEC The Toto Company, 8111 Tyndale Ave.So., Blooming ton, MN 55420-1196, USA ‘Toto Recycler® 8900101 + 21020 21022 =72db (A} Blooming ton, MN, USA VP Technical Man agar 23.01.
TOR 2 Safety 24 General Notes 22 Proper Use 23 Improper Use 24 Preparing the lawn mower for safe operation 25 Safe operation 26 Safe maintenance and storage 27 List of symbols 21 General notes 1. Read the instructions carefully. Familiarize yourself with the operating elements and the proper use of the unit. 2. Children as well as persons who are not familiar with the instructions for use must not operate the lawn Observe the local age limits for the operation of the unit, 3.
A 2.6 Sadie maintenance and storage 1. Ensure that all nuts, bolts and screws are tightened to guarantees a safe operating stet 2. I there is fuse in the tank, never place the mower where there is danger halt the gasoline vapors might catch fire from open flames or sparks. 3. Let tha motor cool down before you put the mower into & closed room. 4. I order to avoid fire risk, keep the area of motor, exhaust, battery case and fuel Lank fare from grass, leaves or excessive amounts of greasily, 5.
TOR ©1998 by The Tore Company Assembly and start-up Become acquainted with your lawn mower Setting the lawn mower up Mounting the wheels Mounting the handlebar Attaching the grass collecting device Adjusting the citing height Proper cutting height Filling in the motor ail Filling up the tank Become acquainted with your lawn mower Safety lever for motor portraitist Function refer to chapter start-up Height adjustment of handlebar Push button tor adjustment of cutting bright (6 steps) Cutting height scale Pea
3.2 Setting the lawn mower up 1. Open the tapes and lift the upper part of the canter (Fig. 2). 2. Take out the components and put them down (Fig. 2). 3, Check completeness of constants. Dispose packaging according to the local regulations. 3.3 Mounting the wheels Note; First mount the wheel bearing with the "Smart Wheel” scale on the deft in the back. 1. Push the wheel bearing the "Smart-Wheel* scale on the left hand side in the back onto the axle until engaged (Fig. 3). 2.
© 1988 by The York Company 3.5 Attaching the grass-collecting device 1. Puttee fabric of the collecting sack from behind onto the frame (Fig. 8). Slide the upper plastic profile underneath the handle to the front and sip it there. 2. clip the other plastic profiles around the frame, 3. clip the plastic profile (Fig. 10} 3.8 Adjusting the cutting height Adjust cutting height only when the motor is turned off, The citing height is adjustable with a six-step central height adjustment, 1.
¥ 10 TOR 3.8 Refiling the motor off (Fig. 14} With outsides temperatures above 4°C, use SAE W-40 HD. With temperatures below 4°C, use SAE 5 W-20 or 5 W-30 HDL . Place mower on a horizontal surface, Open cover and fill in approx. 0.6 fighters of motor oil and insert ol measuring stick up o its limit stop {do not screw in). Take out ol measuring stick and check oit level Ol level may not be above the "Full” mark and not below the "ADD" mark. If required, drain some of the oil. Moo= w 4.
© 1998 by The Toto Company 4 Operation 4.1 Starting and turning off the motor 4.2 Recycling 4.3 Mowing with grass-collecting device 44 Mowing without grass-collecting device 4.1 Starting and turning off the motor Starting the motor 1. Plug spark plug connector on the spark plug (Fig. 16) 2 Place mower on a fiat surface without high grass. 3 it the motor is cold, press the primer button three times (Fig.17).
TOR 42 Recycling Far recycling the Recycle plug must be inside the ejection channel. 1. Ensure that the motor and the cutter stand still. 2. Open the ejection door. 3. Push the Recycle plug into the refection channel. The Recyclable plug must lock (Fig 19). 4. Close the ejection door To remove the Recycle plug, stop the motor and wait until the cutter stands still Open the section road and pull the Recycling plug out. Close the section door. » Ensure that the cutter is always sharp.
© 1998 by The Toto Company Shouts the motor have sapped due fo the conditions inside the mower housing and block when restarting, if is absolutely necessary to clear the mowing tunnel from grass rests (Fig, 21). CE Ta clean the mower, remove the spark plug connector. Change the mowing direction frequently (Fig. 22). In case of an unsatisfactory mowing result; 1. Resharpen the cuties (Ensure not to create an unbalance). 2 Mow at a slower pace, 3. increase the cutting height by one or two steps. 4.
TOR 44 Mowing without the grass-collecting device Never remove the grass-collecting device while the motor is dunning danger of jury! Mowing without the grass-collecting device is recommended for mowing high grass of if no grass collection is desired, Remove the grass-collecting device and the bicycler-piug (Fig. 25 +26).
© 1998 by The Toto Company § Maintenance and upkeep §.1 Checking the cutter for damages 5.2 Cleaning the mower 53 Servicing the air filter 5.4 Exchanging the motor oil 5.5 Exchanging the spark plug 5.8 Storing the mower 5.1 Checking the cutter for damages Stop the motor, wait anvil the cutters stand still and remove the spark plug connector, when working on the mower, Danger of injury After the mower has hit against a hard object as 2 9.
TOR 52 Cleaning the mower Before cleaning fhe maser. stop the motor, wait until the cutlers stand steel and disconnect the spark pug connector. Danger of injury! (Fig. 29) Do not wash the motor down with water. Danger of motor breakdown! Before lilting the mower, fully empty the fuse tank. Only tilt mower far enough that the carburetor is on top. Wipe off dirt and grass rests with a rag. Lay mower on its siege and clean the bot torn side of the mower (Fig. 30).
54 Exchanging the motor ¢il Stop the motor, wait until the cutters stand still and remove the spark plug connector, when working on the mower. Danger of injury! first oll exchange: after 5 patting hours. all offer il exchanges: after 50 operating hours each, but at least one a year. Let motor run for a few minutes before exchanging the oil, Ol brands: with outside temperatures of above 4°C | use SAE 1OW30 HD or 10W40 HD, With temperatures of below 4°C | use BAE SW HD or 5W30 HD. 1.
TOR 55 Exchanging the spark plug Stop the motor, wait until the cutters stand steel and remove the spark plug connector, when working on the mower. Danger of jury! Persons with cardiac pacemakers may not work on the running mayor and on five parts of the ignition stern when the motor is started. it must be ensured that the motor is at standstill. Only then may the spark plug connector be puled off, 1. Gulf spark plug connector off the spark plug (Fig. 35). 2. Clean area around the spark plug 3.
TOR © 1288 by The Toto Company 56 Storing the mower Remove the spark plug connector, Clean the mower. Check all bolts, screws and nuts. Replace damaged parts Use only original TROD spare pants resp. go to 2 specialized TOR-dsaler Before longer storage, empty fuse tank and fet the motor run to fully consume all the fus! Store the mower in a clean, dry place. The handlebar may be folded down for this purpose (Fig. 37).
TOR 6 Spare parts and troubleshooting 6.5 Hints on spare parts ordering 6.2 Customer service address 6.3 Troubleshooting 6.1 Hints on spare parks gardening Use only original TOR spare parts or parts released by the manufacturer. This is the only way to guarantee for your salty and the safely of others, The nameplate bears type and serial number of your TOR lawn mower (Fig. 38). Always give both numbers when ordering spare parts or corresponding.
TOR TROUBLESHOOTING Problem Possible cause Remedial measures Mo tar does not start Fuel tank is empty. 1 Refill tel tank. housing are blocked. 2. Air filter element is dirty. 2. Clean ait fighter element. 3. Spark plug is Jose. 3. Tighten spark plug. Torque: 20 N, 4. High voltage cable is loose or has coma off | 4. Attach bi voltage cable ta spark plug. the spark plug. 5. Electrode distance is not correct. 5. Adjust electrode distance o 0.75 mm. 6. Spark plug is defective. 6. Mount new spark plug. 7.
TROUBLESHOOTING TOR Problem Possible cause Remedial measures Motor overheated. Cooling air flow is obstructed. Electrode distance of spark plug incorrect. Wrong spark plug. Glean vent openings in the hood, in the fan housing and the cooing fins on the motor. Adjust electrode distance to 0.75 mm. Mount correct spark plug with an electrode distance of 6.75 mm. Motor has irregular vibrations. Cutter screw is loose. Cutter has not been balanced. There is toe much grass in the mowing channel.
TOR 7 Hints on tending the lawn 7.1 Spring 7.2 Summer 73 Autumn 74 Winter 7.1 Spring Cleaning: Tha first cut and the cleaning should be done two or three weeks before the normal growth steins, To mow, the cutting height should be adjusted in such way that approx. 1.5 cm of the sorting grass will be cut off, Thus an early greening of the lawn wil be effected. In using the grass-collecting sack available as accessory, the winter litter can be removed. first, however, metal objects, stores. broken glass etc.