Operator's Manual

ManualsBrandsToro ManualsLawn MowersTimeMaster 30 in. Briggs & Stratton Electric Start Walk-Behind Gas Self-Propelled Mower with Spin-Stop

FormNo.3437-159RevA

TimeMaster

30inLawnMower

ModelNo.21199—SerialNo.405600000andUp

ModelNo.21199HD—SerialNo.404314000andUp

ModelNo.21200—SerialNo.405700000andUp

Operator'sManual

Introduction

Thisrotary-blade,walk-behindlawnmowerisintended

tobeusedbyresidentialhomeowners.Itisdesigned

primarilyforcuttinggrassonwell-maintainedlawnson

residentialproperties.Usingthisproductforpurposes

otherthanitsintendedusecouldprovedangerousto

youandbystanders.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Visitwww.T oro.comformoreinformation,including

safetytips,trainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writetheproductmodelandserial

numbersinthespaceprovided.

Important:Withyourmobiledevice,youcan

scantheQRcodeontheserialnumberdecal(if

equipped)toaccesswarranty,parts,andother

productinformation.

g310939

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

ItisaviolationofCaliforniaPublicResourceCode

Section4442or4443touseoroperatetheengineon

anyforest-covered,brush-covered,orgrass-covered

landunlesstheengineisequippedwithaspark

arrester,asdenedinSection4442,maintainedin

effectiveworkingorderortheengineisconstructed,

equipped,andmaintainedforthepreventionofre.

Theenclosedengineowner'smanualissupplied

forinformationregardingtheUSEnvironmental

ProtectionAgency(EPA)andtheCaliforniaEmission

ControlRegulationofemissionsystems,maintenance,

andwarranty.Replacementsmaybeorderedthrough

theenginemanufacturer.

GrossorNetTorque:Thegrossornettorque

ofthisenginewaslaboratoryratedbytheengine

manufacturerinaccordancewiththeSocietyof

AutomotiveEngineers(SAE)J1940orJ2723.As

conguredtomeetsafety,emission,andoperating

requirements,theactualenginetorqueonthisclass

ofmowerwillbesignicantlylower.Pleasereferto

theenginemanufacturer’sinformationincludedwith

themachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedinMexico

AllRightsReserved

*3437-159*A

Summary of content (32 pages)

PAGE 1
Form No. 3437-159 Rev A TimeMaster® 30in Lawn Mower Model No. 21199—Serial No. 405600000 and Up Model No. 21199HD—Serial No. 404314000 and Up Model No. 21200—Serial No. 405700000 and Up Operator's Manual Introduction This rotary-blade, walk-behind lawn mower is intended to be used by residential homeowners. It is designed primarily for cutting grass on well-maintained lawns on residential properties.
PAGE 2
Contents WARNING CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
PAGE 3
Safety • Keep bystanders and children out of the operating area. Do not allow children to operate the machine. Allow only people who are responsible, trained, familiar with the instructions, and physically capable to operate the machine. This machine has been designed in accordance with ANSI B71.1-2017. • Stop the machine, shut off the engine, remove General Safety the ignition key (if equipped), and wait for all moving parts to stop before servicing, fueling, or unclogging the machine.
PAGE 4
decal125-5092 125-5092 1. Step here when starting the engine. decal131-4514 131-4514 1. Warning—read the Operator's Manual. 2. Cutting/dismemberment hazard of hand, mower blade—stay away from moving parts; keep all guards and shields in place. 3. Cutting/dismemberment hazard of hand, mower blade—disconnect the spark-plug wire before performing maintenance. 4. Thrown object hazard—keep bystanders away; shut off the engine before leaving the operating position; pick up any debris before mowing. 5.
PAGE 5
Setup Important: Remove and discard the protective plastic sheet that covers the engine and any other plastic or wrapping on the machine. Important: To prevent accidental starting, do not insert the key into the electric-start ignition (if equipped) until you are ready to start the engine. 1 Assembling and Unfolding the Handle No Parts Required Procedure WARNING Assembling and unfolding the handle improperly can damage the cables, causing an unsafe operating condition.
PAGE 6
2 Installing the Blade-Control Bar No Parts Required Procedure g225133 Figure 4 6
PAGE 7
3 Adding Oil to the Engine No Parts Required Procedure Important: If the oil level in the engine is too low or too high and you run the engine, you may damage the engine. g222533 Figure 5 4 5 Assembling the Grass Bag Charging the Battery No Parts Required No Parts Required Procedure Procedure Electric-Start Model Only Refer to Charging the Battery (page 22).
PAGE 8
Product Overview g289303 Figure 8 Upper handle 1. Adjustment for the self-propel drive 4. Blade-control bar 2. Traction-assist handle 5. Ignition key (electric-start model only) 3. Blade-control-bar lock 6. Ignition switch (electric-start model only) or engine-shutoff switch (standard model only) g289302 Figure 7 1. Side-discharge deflector 10. Battery (electric-start model only; not shown) 2. Spark plug 11. Fuel-tank cap 3. Recoil-start handle 4. Oil fill/dipstick 12. Rear deflector 13.
PAGE 9
Operation – Avoid prolonged breathing of vapors. Note: Determine the left and right sides of the – Keep your hands and face away from the nozzle and the fuel-tank opening. machine from the normal operating position. – Keep fuel away from your eyes and skin.
PAGE 10
Checking the Engine-Oil Level Service Interval: Before each use or daily Important: If the oil level in the crankcase is too low or too high and you run the engine, you may damage the engine. g222533 Figure 11 Adjusting the Handle Height You may raise or lower the handle to a position comfortable for you. Pull the handle-lock lever rearward to disengage the handle-lock pins, move the handle to 1 of 4 positions, and release the handle-lock lever to secure the handle in place. (Figure 12).
PAGE 11
Adjusting the Cutting Height CAUTION If the engine has been running, the muffler will be hot and can burn you. Keep away from the hot muffler. Note: To raise the machine, move the front and rear cutting-height levers forward; to lower the machine, move the cutting-height levers rearward. Set all the wheels to the same height unless special circumstances require otherwise; refer to Operating Tips (page 18).
PAGE 12
During Operation to stop, and disconnect the wire from the spark plug before examining the machine for damage. Make all necessary repairs before resuming operation. During Operation Safety • Before leaving the operating position, shut off the engine, remove the ignition key (electric-start model only), and wait for all moving parts to stop.
PAGE 13
Starting the Engine Standard Model Pull the recoil handle slowly until you feel resistance, then pull it sharply. Allow the rope to return to the engine slowly. Note: If the machine does not start after several attempts, contact an Authorized Service Dealer. g234917 Figure 14 Electric-start Model You can start the engine on an electric-start model by using either the ignition key or the recoil-start handle. • Ignition Key: 1.
PAGE 14
• Recoil-Start Handle: 1. Turn the ignition key to the RUN position (A of Figure 16). Important: Do not attempt to start the engine with the blade-control bar engaged; otherwise, you may blow the fuse (B of Figure 16). 2. Pull the recoil handle slowly to the rear until you feel resistance, then pull sharply (C of Figure 16). Allow the rope to return to the engine slowly.
PAGE 15
Shutting Off the Engine Engaging the Blades Standard Model When you start your engine, the blades do not turn. You must engage the blades to mow. 1. Press the toggle switch (Figure 18) to the STOP position and hold it until the engine shuts off. Pull the blade-control-bar lock back to the blade-control bar (Figure 20). g016484 Figure 20 1. Blade-control bar lock 2. Blade-control bar g311442 Figure 18 Electric-Start Model 1. Turn the ignition key to the OFF position (A of Figure 19). 2.
PAGE 16
10. machine immediately and contact an Authorized Service Dealer. Note: If the newspaper ball did not go under the machine, repeat steps 4 through 10. Checking the Blade-Stop System Operation 11. Service Interval: Before each use or daily Check that the blades stop within 3 seconds of releasing the blade-control bar. This machine comes from the factory ready to recycle grass and leaf clippings back into the lawn.
PAGE 17
Bagging the Clippings Use the grass bag when you want to collect grass and leaf clippings from the lawn. If the side-discharge chute is on the mower, remove it before bagging the clippings; refer to Removing the Side-Discharge Chute (page 18). Installing the Grass Bag 1. Raise and hold up the rear door (A of Figure 24). 2. Remove the rear-discharge plug by pulling down on the latch with your thumb and pulling the plug out from the machine (B of Figure 24). 3.
PAGE 18
g244855 Figure 25 Removing the Side-Discharge Chute To remove the side-discharge chute, reverse the steps in Installing the Side-Discharge Chute (page 17). Operating Tips • Alternate the mowing direction. This helps disperse the clippings over the lawn for even fertilization. General Mowing Tips • If the finished lawn appearance is unsatisfactory, • Inspect the area where you will use the machine try 1 or more of the following: and remove all objects that the machine could throw.
PAGE 19
After Operation After Operation Safety General Safety • Always shut off the machine, remove the ignition key (if equipped), wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it. • Clean grass and debris from the machine to help prevent fires. Clean up oil or fuel spills. • Never store the machine or fuel container where g003934 Figure 26 there is an open flame, spark, or pilot light, such as on a water heater or on other appliances. 1.
PAGE 20
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 5 hours • Change the engine oil. Before each use or daily • • • • • Check the engine-oil level and add oil as needed. Check the blade-brake-clutch operation. Clean grass clippings and dirt from under the machine. Check the air filter and clean or replace it, if necessary. Check the cutting blades. Every 25 hours • Charge the battery for 24 hours (electric-start model only).
PAGE 21
WARNING Tipping the machine may cause the fuel to leak. Fuel is flammable, explosive, and can cause personal injury. 4. Install the filter onto the base. 5. Install the cover and screw the fastener down securely. Changing the Engine Oil Run the engine dry or remove the fuel with a hand pump; never siphon. Service Interval: After the first 5 hours Every 50 hours Yearly Servicing the Air Filter Service Interval: Before each use or daily—Check the air filter and clean or replace it, if necessary.
PAGE 22
Charging the Battery Electric-Start Model Only Service Interval: Every 25 hours Yearly or before storage Charge the battery for 24 hours initially, then monthly (every 25 starts) or as needed. Always use the charger in a sheltered area, and charge the battery at room temperature (about 22°C or 70°F) whenever possible. g017281 Figure 30 Note: The machine is not equipped with an alternator 5. 6. Carefully pour about 3/4 of the engine capacity of oil into the oil-fill tube. 7.
PAGE 23
Replacing the Fuse Electric-Start Model Only If the battery does not charge or the engine does not run with the electric starter, the fuse may be blown. Replace it with a 40 A plug-in type fuse. Important: You cannot start the machine with the electric starter or charge the battery unless a working fuse is installed. 1. Open the sealed fuse holder and replace the fuse (Figure 32). g017523 Figure 33 1. Rear door and handle-lock-lever assembly 8. Remove the cover from the battery. 9.
PAGE 24
Adjusting the Self-Propel Drive Servicing the Blade-Drive System For Self-Propel-Drive Models Only Service Interval: Every 50 hours 1. Whenever you install a new self-propel cable or if the self-propel drive is out of adjustment, adjust the self-propel drive. 1. Remove the blade-drive system cover (Figure 35). Turn the adjustment nut counterclockwise to loosen the cable adjustment (Figure 34). g016491 Figure 35 1. Bolts g269307 2. Cover Figure 34 1. Handle (left side) 4.
PAGE 25
4. Install the blade-drive system cover that you previously removed. Servicing the Blades Service Interval: Yearly Important: You will need a torque wrench to install the blades properly. If you do not have a torque wrench or are uncomfortable performing this procedure, contact an Authorized Service Dealer. Examine the blades whenever you run out of fuel. If the blades are damaged or cracked, replace them immediately.
PAGE 26
Checking for Bent Blades WARNING If you allow a blade to wear, a slot will form between the sail and flat part of the blade. Eventually a piece of the blade may break off and be thrown from under the housing, possibly resulting in serious injury to you or bystanders. 1. Rotate the blades to the position shown in Figure 39. • Inspect the blade periodically for wear or damage. • Never try to straighten a blade that is bent or weld a broken or cracked blade. • Replace a worn or damaged blade. 3.
PAGE 27
Removing the Blades Installing the Blades 1. Replace the blades when the machine hits a solid object or when a blade is out of balance or bent. Use only genuine Toro replacement blades. 1. Install the first blade so that it is horizontal, along with all mounting hardware as shown in Figure 41. Note: Tighten the bolt with your fingers. Use a block of wood to hold each blade steady and turn the blade bolt counterclockwise as shown in Figure 40.
PAGE 28
Storage Store the machine in a cool, clean, dry place. Storage Safety Always shut off the machine, remove the ignition key (if equipped), wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it. g016536 Figure 43 1. Blade (2) General Information 4. Tighten the second blade; refer to step 2. 1. 5. Rotate the blades by hand a full 360° turn to ensure that they do not touch.
PAGE 29
Empty the fuel tank when mowing the last time before storing the machine. 1. Run the machine until the engine shuts off from running out of fuel. 2. Start the engine again and allow it to run until it shuts off. When you can no longer start the engine, it is sufficiently dry. Preparing the Engine 1. While the engine is still warm, change the engine oil; refer to Changing the Engine Oil (page 21). 2. Disconnect the wire from the spark plug and remove the ignition key (electric-start model only). 3.
PAGE 30
Notes:
PAGE 31
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
PAGE 32