Operator's Manual

ManualsBrandsToro ManualsWalk-Behind Mowers55cm Recycler Lawn Mower

FormNo.3437-140RevA

55cmRecycler

LawnMower

ModelNo.21762—SerialNo.405500000andUp

ModelNo.21763—SerialNo.405559501andUp

Operator'sManual

Introduction

Thisrotary-blade,walk-behindlawnmowerisintended

tobeusedbyresidentialhomeowners.Itisdesigned

primarilyforcuttinggrassonwell-maintainedlawnson

residentialproperties.Usingthisproductforpurposes

otherthanitsintendedusecouldprovedangerousto

youandbystanders.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Visitwww.Toro.comformoreinformation,including

safetytips,trainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

Important:Withyourmobiledevice,youcan

scantheQRcodeontheserialnumberdecal(if

equipped)toaccesswarranty,parts,andother

productinformation

g282707

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

ThisproductcomplieswithallrelevantEuropean

directives;fordetails,pleaseseetheseparateproduct

specicDeclarationofConformity(DOC)sheet.

Theenclosedengineowner'smanualissupplied

forinformationregardingtheUSEnvironmental

ProtectionAgency(EPA)andtheCaliforniaEmission

ControlRegulationofemissionsystems,maintenance,

andwarranty.Replacementsmaybeorderedthrough

theenginemanufacturer.

GrossorNetTorque:Thegrossornettorque

ofthisenginewaslaboratoryratedbytheengine

manufacturerinaccordancewiththeSocietyof

AutomotiveEngineers(SAE)J1940orJ2723.As

conguredtomeetsafety,emission,andoperating

requirements,theactualenginetorqueonthisclass

ofmowerwillbesignicantlylower.Pleasereferto

theenginemanufacturer’sinformationincludedwith

themachine.

Donottamperwithordisablesafetydevicesonthe

machine,andchecktheirproperoperationregularly.

Donotattempttoadjustortamperwiththeengine

speedcontrol;doingsomaycreateanunsafe

operatingcondition,resultinginpersonalinjury.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedinMexico

AllRightsReserved

*3437-140*A

Summary of content (28 pages)

PAGE 1
Form No. 3437-140 Rev A 55cm Recycler® Lawn Mower Model No. 21762—Serial No. 405500000 and Up Model No. 21763—Serial No. 405559501 and Up Operator's Manual Introduction This rotary-blade, walk-behind lawn mower is intended to be used by residential homeowners. It is designed primarily for cutting grass on well-maintained lawns on residential properties. Using this product for purposes other than its intended use could prove dangerous to you and bystanders.
PAGE 2
Contents Safety Introduction ............................................................... 1 Safety ....................................................................... 2 General Safety ................................................... 2 Safety and Instructional Decals .......................... 3 Setup ........................................................................ 5 1 Assembling and Unfolding the Handle.............. 5 2 Installing the Recoil-Starter Rope in the Rope Guide...............
PAGE 3
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decaloemmarkt Manufacturer's Mark 1. This mark indicates that the blade is identified as a part from the original machine manufacturer. decal112-8760 112-8760 1. Thrown object hazard—keep bystanders away. 2. Cutting/dismemberment hazard of hand or foot, mower blade—stay away from moving parts.
PAGE 4
decal131-4514 131-4514 1. Warning—read the Operator's Manual. 2. Cutting/dismemberment hazard of hand, mower blade—stay away from moving parts; keep all guards and shields in place. 3. Cutting/dismemberment hazard of hand, mower blade—disconnect the spark-plug wire before performing maintenance. 4. Thrown object hazard—keep bystanders away; shut off the engine before leaving the operating position; pick up any debris before mowing. 5.
PAGE 5
Setup Important: Remove and discard the protective plastic sheet that covers the engine and any other plastic or wrapping on the machine. Important: To prevent accidental starting, do not insert the electric-start button into the electric-start ignition (if equipped) until you are ready to start the engine. 1 Assembling and Unfolding the Handle No Parts Required Procedure Note: Ensure that the cables are routed on the outside of the handle and are not pinched (D of Figure 3).
PAGE 6
2 Installing the Recoil-Starter Rope in the Rope Guide No Parts Required Procedure Important: To start the engine safely and easily whenever you use the machine, install the recoil-starter rope in the rope guide. g230719 Figure 4 3 Adding Oil to the Engine No Parts Required Procedure Important: If the oil level in the engine is too low or too high and you run the engine, you may damage the engine.
PAGE 7
g222533 Figure 5 4 Assembling the Grass Bag No Parts Required Procedure g230447 Figure 6 5 Charging the Battery No Parts Required Procedure Electric-Start Model Only Refer to Charging the Battery (page 21).
PAGE 8
Product Overview g009526 Figure 8 3. Battery charger (electric-start model only) 1. Grass bag 2. Side-discharge chute Specifications Model 21762 21763 g274818 Figure 7 1. Handle 2. Blade-control bar 9. Air filter 10. Spark plug 3. Adjustment for the self-propel drive 11.
PAGE 9
Operation – Avoid prolonged breathing of vapors. Note: Determine the left and right sides of the – Keep your hands and face away from the nozzle and the fuel-tank opening. machine from the normal operating position. – Keep fuel away from your eyes and skin.
PAGE 10
Filling the Fuel Tank Fill the fuel tank with fresh unleaded regular gasoline from a major name-brand service station (Figure 9). • For best results, use only clean, fresh, unleaded Important: To reduce starting problems, add fuel gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). stabilizer/conditioner to fresh fuel as directed by the fuel-stabilizer manufacturer. • Oxygenated fuel with up to 10% ethanol or 15% Refer to your engine owner’s manual for additional information.
PAGE 11
Adjusting the Handle Height You can raise or lower the handle in 1 of 2 positions that is more comfortable for you (Figure 11). g269686 Figure 11 1. Remove both handle knobs. 2. Move the handle to the desired height position. 3. Secure the handle with the previously removed handle knobs. Adjusting the Cutting Height CAUTION If the engine has been running, the muffler will be hot and can burn you. Keep away from the hot muffler. Adjust the cutting height as desired.
PAGE 12
During Operation • Use extreme care when approaching blind During Operation Safety • Do not direct the discharge material toward corners, shrubs, trees, or other objects that may block your view. anyone. Avoid discharging material against a wall or obstruction; material may ricochet toward you. Stop the blade(s) when crossing gravel surfaces.
PAGE 13
g239637 Figure 13 Starting the Engine Using the Recoil-Start Handle 1. Hold the blade-control bar against the handle (A of Figure 14). 2. Pull the recoil-start handle (B of Figure 14). Note: When you pull the recoil-start handle, pull it lightly until you feel resistance, then pull it sharply. Allow the rope to return to the handle slowly. Note: If the machine does not start after several attempts, contact an Authorized Service Dealer.
PAGE 14
If the grass bag is on the machine and the bag-on-demand lever is in the bagging position, move the lever to the recycling position; refer to Operating the Bag-on-Demand Lever (page 14). If the side-discharge chute is on the machine, remove it; refer to Removing the Side-Discharge Chute (page 15). using your machine immediately and contact an Authorized Service Dealer. Recycling the Clippings Your machine comes from the factory ready to recycle the grass and leaf clippings back into the lawn.
PAGE 15
move the lever rearward until the button on the lever pops up. Important: For proper operation, shut off the engine, wait for all moving parts to stop, and then remove any grass clippings and debris from the bag-on-demand door and the surrounding opening (Figure 18) before you move the bag-on-demand lever from 1 position to another. g235646 Figure 19 Removing the Side-Discharge Chute g027454 Figure 18 1.
PAGE 16
After Operation • Wet grass and leaves tend to clump on the yard and can cause the machine to plug or the engine to stall. Avoid mowing in wet conditions. After Operation Safety • Be aware of a potential fire hazard in very dry conditions, follow all local fire warnings, and keep the machine free of dry grass and leaf debris. General Safety • Alternate the mowing direction. This helps • Always shut off the machine, remove the disperse the clippings over the lawn for even fertilization.
PAGE 17
g009501 Figure 20 1. Washout port 6. Turn the water on. 7. Start the engine and run it until the clippings no longer come out from under the machine. 8. Shut off the engine. 9. Shut off the water and disconnect the garden hose from the machine. 1. Electric starter 10. Start the engine and run it for a few minutes to dry the underside of the machine to prevent it from rusting. 2. 11.
PAGE 18
g032870 Figure 23 1. Operating position 2. Folded position g032865 4. Insert the carriage bolt (with the bolt head toward the inside) through the handle bracket and the upper hole in the handle end. Ensure that the square edges of each carriage bolt fits into the upper or lower square hole in its related handle bracket (Figure 24). Figure 24 1. Handle knob 5. 6. 2. Carriage bolt Loosely install the handle knobs and carriage bolts on the handle brackets.
PAGE 19
personal injury. Run the engine dry or remove the fuel with a hand pump; never siphon the fuel. • To ensure optimum performance of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty. Preparing for Maintenance 1. Shut off the engine, remove the electric-start button (if equipped), and wait for all moving parts to stop. 2.
PAGE 20
Servicing the Air Filter Changing the Engine Oil Service Interval: Every 25 hours Service Interval: Yearly Yearly 1. Changing the engine oil is not required, but if you want to change the oil, use the following procedure. Unclip the top of the air-filter cover (Figure 26). Note: Run the engine a few minutes before changing the oil to warm it. Warm oil flows better and carries more contaminants. Engine Oil Specifications Engine oil capacity 0.
PAGE 21
Charging the Battery For Electric-Start Models Service Interval: Every 25 hours Charge the battery for 24 hours initially, then monthly (every 25 starts) or as needed. Always use the charger in a sheltered area and charge the battery at room temperature (22°C or 70°F) whenever possible. 1. Connect the charger to the wire harness located below the electric-start button (Figure 29). g032618 Figure 28 5. After draining the used oil, return the machine to the operating position. 6.
PAGE 22
Replacing the Fuse 4. Note: Your machine comes with a spare fuse in For Electric-Start Models the battery compartment. If the battery does not charge or the engine does not run with the electric starter, the fuse may be blown. Replace it with a 40 A plug-in type fuse. 1. Raise the rear deflector and locate the battery compartment (Figure 30). g009506 Figure 30 1. Rear deflector 3. Battery 2. Screw 4. Battery compartment 2. Wipe away any debris from the battery compartment area. 3.
PAGE 23
Replacing the Blade Service Interval: Yearly Important: You will need a torque wrench to install the blade properly. If you do not have a torque wrench or are uncomfortable performing this procedure, contact an Authorized Service Dealer. Examine the blade whenever you run out of fuel. If the blade is damaged or cracked, replace it immediately. If the blade edge is dull or nicked, have it sharpened and balanced, or replace it.
PAGE 24
Adjusting the Self-Propel Drive Storage Store the machine in a cool, clean, dry place. For Self-Propel-Drive Models Only Storage Safety Whenever you install a new self-propel cable or if the self-propel drive is out of adjustment, adjust the self-propel drive. 1. Always shut off the machine, remove the electric-start button (if equipped), wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it.
PAGE 25
Removing the Machine from Storage 1. Electric-start models only: Charge the battery for 24 hours; refer to Charging the Battery (page 21). 2. Check and tighten all fasteners. 3. Remove the spark plug and spin the engine rapidly by pulling the recoil-start handle to blow the excess oil from the cylinder. 4. Install the spark plug and tighten it with a torque wrench to 20 N∙m (15 ft-lb). 5. Perform any maintenance procedures; refer to Maintenance (page 18). 6.
PAGE 26
Notes:
PAGE 27
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
PAGE 28