Operator's Manual

ManualsBrandsToro ManualsWalk-Behind MowersTimeMaster 76cm Lawn Mower

FormNo.3431-927RevA

TimeMaster

76cmLawnMower

ModelNo.21810—SerialNo.400000000andUp

ModelNo.21811—SerialNo.400000000andUp

Operator'sManual

Introduction

Thisrotary-blade,walk-behindlawnmowerisintended

tobeusedbyresidentialhomeowners.Itisdesigned

primarilyforcuttinggrassonwell-maintainedlawnson

residentialproperties.Usingthisproductforpurposes

otherthanitsintendedusecouldprovedangerousto

youandbystanders.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Visitwww.Toro.comformoreinformation,including

safetytips,trainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourmachineready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

Important:Withyourmobiledevice,youcan

scantheQRcodeontheserialnumberdecal(if

equipped)toaccesswarranty,parts,andother

productinformation

g226630

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

ThisproductcomplieswithallrelevantEuropean

directives;fordetails,pleaseseetheseparateproduct

specicDeclarationofConformity(DOC)sheet.

GrossorNetTorque:Thegrossornettorque

ofthisenginewaslaboratoryratedbytheengine

manufacturerinaccordancewiththeSocietyof

AutomotiveEngineers(SAE)J1940orJ2723.As

conguredtomeetsafety,emission,andoperating

requirements,theactualenginetorqueonthisclass

ofmowerwillbesignicantlylower.Pleasereferto

theenginemanufacturer’sinformationincludedwith

themachine.

Donottamperwithordisablesafetydevicesonthe

machine,andchecktheirproperoperationregularly.

Donotattempttoadjustortamperwiththeengine

speedcontrol;doingsomaycreateanunsafe

operatingcondition,resultinginpersonalinjury.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedinMexico

AllRightsReserved

*3431-927*A

Summary of content (32 pages)

PAGE 1
Form No. 3431-927 Rev A TimeMaster® 76cm Lawn Mower Model No. 21810—Serial No. 400000000 and Up Model No. 21811—Serial No. 400000000 and Up Operator's Manual Introduction serious injury or death if you do not follow the recommended precautions. This rotary-blade, walk-behind lawn mower is intended to be used by residential homeowners. It is designed primarily for cutting grass on well-maintained lawns on residential properties.
PAGE 2
Contents Removing the Machine from Storage ................ 30 Introduction ............................................................... 1 Safety ....................................................................... 3 General Safety ................................................... 3 Safety and Instructional Decals .......................... 4 Setup ........................................................................ 5 1 Assembling and Unfolding the Handle..............
PAGE 3
Safety This machine has been designed in accordance with EN ISO 5395. General Safety This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury. • Read, understand, and follow the instructions and warnings in this Operator’s Manual and on the machine and attachments before starting the engine. • Do not put your hands or feet near moving parts of or under the machine. Keep clear of any discharge opening.
PAGE 4
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decaloemmarkt Manufacturer's Mark 1. This mark indicates that the blade is identified as a part from the original machine manufacturer. decal104-7953 104-7953 Electric-Start Model Only 1. Warning—read the Operator's Manual for information on charging the battery; contains lead; do not discard. 2.
PAGE 5
Setup Important: Remove and discard the protective plastic sheet that covers the engine and any other plastic or wrapping on the machine. Important: To prevent accidental starting, do not decal131-4514 131-4514 insert the key into the electric-start ignition (if equipped) until you are ready to start the engine. 1. Warning—read the Operator's Manual. 2. Cutting/dismemberment hazard of hand, mower blade—stay away from moving parts; keep all guards and shields in place. 3.
PAGE 6
g224528 Figure 3 2 Installing the Blade-Control Bar No Parts Required Procedure g225133 Figure 4 6
PAGE 7
3 Filling the Crankcase with Oil No Parts Required Procedure Important: If the oil level in the crankcase is too low or too high and you run the engine, you may damage the engine.
PAGE 8
Product Overview 5 Charging the Battery No Parts Required Procedure Electric-Start Model Only Refer to Charging the Battery (page 23). g289302 Figure 7 1. Side-discharge deflector 2. Spark plug 11. Fuel-tank cap 3. Recoil-start handle 4. Oil fill/dipstick 12. Rear deflector 13. Rear cutting-height lever 5. Handle-lock lever 6. Handle knob (2) 14. Fuse 15. Air filter 7. Adjustment for the self-propel drive 16. Washout port 8. Upper handle 17. Front cutting-height lever 9.
PAGE 9
Specifications Model 21810 21811 Weight Length Width Height (140 lb) 165 cm 81 cm 114 cm 66 kg (65 inches) (32 inches) (45 inches) 64 kg (145 lb) Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories.
PAGE 10
Fuel Safety 1. • Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Clean around the fuel-tank cap and remove the cap from the tank. Important: This machine is equipped with a premium fuel tank that uses a foam insert to prevent fuel agitation. Never remove the foam element, because it allows the engine to use all the fuel in the tank (A of Figure 10).
PAGE 11
Checking the Engine-Oil Level Service Interval: Before each use or daily Important: If the oil level in the crankcase is too low or too high and you run the engine, you may damage the engine. g222533 Figure 11 Adjusting the Handle Height You may raise or lower the handle to a position comfortable for you. Pull the handle-lock lever rearward to disengage the handle-lock pins, move the handle to 1 of 4 positions, and release the handle-lock lever to secure the handle in place. (Figure 12).
PAGE 12
Adjusting the Cutting Height CAUTION If the engine has been running, the muffler will be hot and can severely burn you. Keep away from the hot muffler. Note: To raise the machine, move the front and rear cutting-height levers forward; to lower the machine, move the cutting-height levers rearward. Set all the wheels to the same height unless special circumstances require otherwise; refer to Operating Tips (page 19).
PAGE 13
• If the engine has been running, it will be hot and • Use extreme care when approaching blind can severely burn you. Keep away from the hot engine. corners, shrubs, trees, or other objects that may block your view. • Operate the engine only in well-ventilated areas. • Do not direct the discharge material toward Exhaust gases contain carbon monoxide, which is lethal if inhaled. anyone. Avoid discharging material against a wall or obstruction; material may ricochet toward you.
PAGE 14
Note: Do not hold the ignition key in the Start position for longer than 5 seconds to prevent burning out the starter motor.
PAGE 15
• Recoil-Start Handle: 1. Turn the ignition key to the RUN position (A of Figure 16). Important: Do not attempt to start the engine with the blade-control bar engaged; otherwise, you may blow the fuse (B of Figure 16). 2. Pull the recoil handle slowly to the rear until you feel resistance, then pull sharply (C of Figure 16). Allow the rope to return to the engine slowly.
PAGE 16
Shutting Off the Engine 1. Pull the blade-control-bar lock back to the blade-control bar (Figure 20). Standard Model Press the toggle switch (Figure 17) to the STOP position and hold it until the engine shuts off. g016484 Figure 20 1. Blade-control bar lock g234921 Figure 18 2. Blade-control bar 2. Slowly pull the blade-control bar back to the handle (Figure 20). 3. Hold the blade-control bar against the handle (Figure 21). Electric-Start Model 1. 2.
PAGE 17
Checking the Blade-Stop System Operation Note: If the newspaper ball did not go under the machine, repeat steps 4 through 10. 11. Service Interval: Before each use or daily Check that the blades stop within 3 seconds of releasing the blade-control bar. Recycling the Clippings Using the Grass Bag This machine comes from the factory ready to recycle grass and leaf clippings back into the lawn. To prepare the machine to recycle, do the following: You can use the grass bag to check the blade-stop system.
PAGE 18
Bagging the Clippings Use the grass bag when you want to collect grass and leaf clippings from the lawn. If the side-discharge chute is on the mower, remove it before bagging the clippings; refer to Removing the Side-Discharge Chute (page 19). Installing the Grass Bag 1. Raise and hold up the rear door (A of Figure 24). 2. Remove the rear-discharge plug by pulling down on the latch with your thumb and pulling the plug out from the machine (B of Figure 24). 3.
PAGE 19
Cutting Leaves Removing the Side-Discharge Chute • After cutting the lawn, ensure that half of the lawn shows through the cut leaf cover. You may need to make more than a single pass over the leaves. To remove the side-discharge chute, lift up the side deflector, remove the side-discharge chute, and lower the side-discharge deflector until it latches securely. • If there are more than 13 cm (5 inches) of leaves on the lawn, mow at a higher cutting height and then again at the desired cutting height.
PAGE 20
g003934 Figure 26 1. Washout fitting 3. O-ring 2. Hose 4. Coupling 5. Start the engine, engage the blade-control lever, and let the machine run for 1 to 3 minutes with the blades turning. 6. Disengage the blade-control lever, shut off the engine, and wait for all moving parts to stop. 7. Shut off the water and remove the coupling from the washout fitting. Note: If the machine is not clean after a single washing, soak it and let it stand for 30 minutes. Then repeat the process. 8.
PAGE 21
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 5 hours • Change the engine oil. Before each use or daily • • • • • Check the engine-oil level and add oil as needed. Check the blade-brake-clutch operation. Clean grass clippings and dirt from under the machine. Check the air filter and clean or replace it, if necessary. Check the cutting blades. Every 25 hours • Charge the battery for 24 hours (electric-start model only).
PAGE 22
WARNING Tipping the machine may cause the fuel to leak. Fuel is flammable, explosive, and can cause personal injury. Run the engine dry or remove the fuel with a hand pump; never siphon. 3. Clean the air-filter body and cover using a damp rag. Keep dirt away from the air opening. 4. Install the filter onto the base. 5. Install the cover and screw the fastener down securely.
PAGE 23
Charging the Battery Electric-Start Model Only Service Interval: Every 25 hours Yearly or before storage Charge the battery for 24 hours initially, then monthly (every 25 starts) or as needed. Always use the charger in a sheltered area, and charge the battery at room temperature (about 22°C or 70°F) whenever possible. g017281 Figure 30 Note: The machine is not equipped with an alternator 5. 6. Carefully pour about 3/4 of the engine capacity of oil into the oil-fill tube. 7.
PAGE 24
Replacing the Fuse Electric-Start Model Only If the battery does not charge or the engine does not run with the electric starter, the fuse may be blown. Replace it with a 40 A plug-in type fuse. Important: You cannot start the machine with the electric starter or charge the battery unless a working fuse is installed. 1. Open the sealed fuse holder and replace the fuse (Figure 32). g017523 Figure 33 1. Rear door and handle-lock-lever assembly 8. Remove the cover from the battery. 9.
PAGE 25
Adjusting the Self-Propel Drive Servicing the Blade-Drive System For Self-Propel-Drive Models Only Service Interval: Every 50 hours 1. Whenever you install a new self-propel cable or if the self-propel drive is out of adjustment, adjust the self-propel drive. 1. Remove the blade-drive system cover (Figure 35). Turn the adjustment nut counterclockwise to loosen the cable adjustment (Figure 34). g016491 Figure 35 1. Bolts g269307 2. Cover Figure 34 1. Handle (left side) 4.
PAGE 26
4. Install the blade-drive system cover that you previously removed. Servicing the Blades Service Interval: Yearly Important: You will need a torque wrench to install the blades properly. If you do not have a torque wrench or are uncomfortable performing this procedure, contact an Authorized Service Dealer. Examine the blades whenever you run out of fuel. If the blades are damaged or cracked, replace them immediately.
PAGE 27
Checking for Bent Blades DANGER If you allow a blade to wear, a slot will form between the sail and flat part of the blade. Eventually a piece of the blade may break off and be thrown from under the housing, possibly resulting in serious injury to you or bystanders. 1. Rotate the blades to the position shown in Figure 39. • Inspect the blade periodically for wear or damage. • Never try to straighten a blade that is bent or weld a broken or cracked blade. • Replace a worn or damaged blade. 3.
PAGE 28
Removing the Blades Installing the Blades 1. Replace the blades when the machine hits a solid object or when a blade is out of balance or bent. Use only genuine Toro replacement blades. 1. Install the first blade so that it is horizontal, along with all mounting hardware as shown in Figure 41. Note: Tighten the bolt with your fingers. Use a block of wood to hold each blade steady and turn the blade bolt counterclockwise as shown in Figure 40.
PAGE 29
g016536 Figure 43 1. Blade (2) 4. Tighten the second blade; refer to step 2. 5. Rotate the blades by hand a full 360° turn to ensure that they do not touch. Note: If the blades touch each other, they are not mounted correctly. Repeat steps 1 through 3, until the blades no longer touch each other. WARNING Incorrectly installing the blades could damage the machine or cause an injury to you or bystanders. Use care when installing the blades.
PAGE 30
Storage On the last refueling of the year, add fuel stabilizer to the fuel as directed by the engine manufacturer. Empty the fuel tank when mowing the last time before storing the machine. Store the machine in a cool, clean, dry place. Storage Safety Always shut off the machine, remove the ignition key (if equipped), wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it.
PAGE 31
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
PAGE 32