Form No. 3440-691 Rev B 48cm 60V Super Recycler® Model No. 21848—Serial No. 400000000 and Up Model No. 21848T—Serial No. 400000000 and Up Register at www.Toro.com.
Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information. This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. Introduction This rotary-blade, walk-behind lawn mower is intended to be used by residential homeowners.
Contents Safety Safety ....................................................................... 3 Safety and Instructional Decals .......................... 6 Setup ........................................................................ 8 1 Mounting the Battery Charger (Optional) ........................................................ 8 2 Unfolding the Handle ....................................... 9 3 Assembling the Grass Bag............................. 10 Product Overview .............................
style of connection, use an attachment plug adapter of the proper configuration for the power outlet if needed. 7. 8. 9. Do not use a damaged or modified battery pack or battery charger, which may exhibit unpredictable behavior that results in fire, explosion, or risk of injury. If the supply cord to the battery charger is damaged, contact an Authorized Service Dealer to replace it.
1. Stop the machine, remove the electric-start button, remove the battery pack from the machine, and wait for all movement to stop before adjusting, servicing, cleaning, or storing the machine. 2. Do not attempt to repair the machine except as indicated in the instructions. Have an Authorized Service Dealer perform service on the machine using identical replacement parts. 3. Wear gloves and eye protection when servicing the machine. 4. Sharpen a dull blade on both sides to maintain balance.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. Model 81860 decal137-9461 137-9461 1. Battery charge status decal137-9489 137-9489 1. Read the Operator’s Manual. 2. Recycle 4. Keep away from open flames. 5. Do not expose to rain. decal112-8760 112-8760 1. Thrown object hazard—keep bystanders away. 3. Contains lithium ions; do not discard. 2.
decal137-9496 137-9496 1. The battery pack is charging. 3. The battery pack is over or under the appropriate temperature range. 2. The battery pack is fully charged. 4. Battery pack charging fault decal119-2283 119-2283 1. Height of cut decal144-6368 144-6368 1. Warning—read the Operator's Manual. 4. Thrown object hazard—keep bystanders away; shut off the machine before leaving the operating position; pick up any debris before mowing. 2.
Setup Note: The battery pack is not fully charged when it is purchased. Before using the machine for the first time, refer to Charging the Battery Pack (page 20). 1 Mounting the Battery Charger (Optional) Parts needed for this procedure: 2 Mounting hardware (not included) Procedure If desired, mount the battery charger securely on a wall using the wall-mount key holes on the back of the charger. Mount it indoors (such as a garage or other dry place), near a power outlet, and out of the reach of children.
2 Unfolding the Handle No Parts Required Procedure WARNING Folding or unfolding the handle improperly can damage the cables, causing an unsafe operating condition. • Do not damage the cables when folding or unfolding the handle. • If a cable is damaged, contact an Authorized Service Dealer. Important: Remove and discard the protective plastic sheet that covers the motor and any other plastic or wrapping on the machine. 1. Loosen the handle knobs (Figure 4). g335758 Figure 4 1. Handle knobs 2.
3 Assembling the Grass Bag No Parts Required Procedure g241560 Figure 6 10
Product Overview Battery Pack Model 81850 6.0 Ah Battery pack capacity 324 Wh Battery manufacturer rating = 60V maximum and 54V nominal. Actual voltage varies with load. Battery Charger Model 81802 Type 60V MAX Lithium-Ion Battery Charger Input 100V to 240V AC 50/60Hz Max 2.0A Output 60V MAX DC 2.0A Appropriate Temperature Ranges 7. Rear deflector 2. Traction-assist handle 8. Washout port (not shown) 3. Blade-control bar 10. Bag-on-demand lever 5. Electric-start switch 11.
Operation Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Installing the Battery Pack Important: Use the battery pack only in temperatures that are within the appropriate range; refer to Specifications (page 11). 1. Make sure that the vents on the battery are clear of any dust and debris. 2. Lift up the battery-compartment lid (A of Figure 9). 3.
Adjusting the Handle Height Adjusting the Cutting Height You may raise or lower the handle to a position comfortable for you. WARNING Adjusting the cutting-height levers could bring your hands into contact with a moving blade and result in serious injury. Rotate the handle lock, move the handle to 1 of 3 positions, and lock the handle into position (Figure 10). • Shut off the machine and wait for all moving parts to stop before adjusting the cutting height.
During Operation Starting the Machine 1. Ensure that the battery pack is installed in the machine; refer to Installing the Battery Pack (page 12). 2. Insert the electric-start button into the electric starter switch (A of Figure 12). 3. Squeeze the blade-control bar and hold it to the handle (B of Figure 12). 4. Press the electric-start button and keep it pressed until the motor starts (C of Figure 12).
Bagging the Clippings Use the grass bag when you want to collect grass and leaf clippings from the lawn. If the bag-on-demand lever is in the recycling position, move it to the bagging position; refer to Operating the Bag-on-Demand Lever (page 15). Installing the Grass Bag 1. Raise and hold up the rear deflector (A of Figure 14). 2. Install the grass bag, ensuring that the pins on the bag rest in the notches on the handle (B of Figure 14). 3. Lower the rear deflector.
Rear-Discharging the Clippings Shutting Off the Machine Use the rear discharge for cutting very tall grass. Note: If the grass bag is on the machine, remove it before rear-discharging the clippings; refer to Removing the Grass Bag (page 15). The bag-on-demand lever should be in the BAGGING position as shown in Figure 15. 1. Release the blade-control bar (A of Figure 18). 2. Remove the electric-start button from the electric starter (B of Figure 18). 3.
Operating Tips • If there are more than 13 cm (5 inches) of leaves on the lawn, mow at a higher cutting height and then again at the desired cutting height. General Mowing Tips • Slow down your mowing speed if the machine • Inspect the area where you will use the machine does not cut the leaves finely enough. and remove all objects that the machine could throw. • Avoid striking solid objects with the blade. Never deliberately mow over any object.
After Operation Cleaning under the Machine Service Interval: Before each use or daily For best results, clean the machine soon after you have completed mowing. 1. Move the machine onto a flat paved surface. 2. Shut off the motor and wait for all moving parts to stop before leaving the operating position. 3. Lower the machine to its lowest cutting-height setting. Refer to Adjusting the Cutting Height (page 13). 4.
Folding the Handle WARNING Folding or unfolding the handle improperly can damage the cables, causing an unsafe operating condition. g335780 Figure 22 • Do not damage the cables when folding or unfolding the handle. 1. Handle knobs • If a cable is damaged, contact an Authorized Service Dealer. 6. 1. Remove the electric-start button (Figure 20). g251571 Figure 20 2. Hold the handle while disengaging the handle locks to avoid pinching your hands. 3. Rotate the entire handle forward (Figure 21).
Charging the Battery Pack Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged. Read all safety precautions. button on the battery pack to display the current charge (LED indicators). Ensure that the vents on the battery and charger are clear of any dust and debris. g290533 Figure 23 5. LED indicators (current charge) 2.
Maintenance Remove the electric-start button and battery pack from the machine before maintaining or cleaning the machine. Always shut off the machine, wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it. Use only the manufacturer’s recommended replacement parts and accessories. Inspect and maintain the machine regularly. Have the machine repaired only by an Authorized Service Dealer. g231389 Figure 24 Lubricating the Machine 4.
Adjusting the Self-Propel Drive Storage Whenever you install a new self-propel cable or if the self-propel drive is out of adjustment, adjust the self-propel drive. charger only in temperatures that are within the appropriate range; refer to Specifications (page 11). 1. Important: Store the machine, battery pack, and Turn the adjustment nut counterclockwise to loosen the cable adjustment (Figure 26).
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The machine does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the machine. 1. Remove and then replace the battery into the machine, making sure that it is fully installed and latched. 2.
Problem The machine is producing a beeping sound. Possible Cause Corrective Action 1. The battery pack is not charged. 1. Remove the battery pack from the machine and charge it. 2. The machine is in an unsafe position for operation. 3. The machine is overloaded. 2. Ensure that the machine is not at an extreme angle while operating. 3. Cut the grass at a higher height of cut or walk at a slower pace while mowing. 4.
Notes:
Notes:
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
