Form No. 3433-504 Rev B Grapple Rake Compact Tool Carriers Model No. 22577—Serial No. 319000001 and Up Register at www.Toro.com.
This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication WARNING CALIFORNIA Proposition 65 Warning Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. g293601 Figure 1 Introduction Model No. This grapple rake is intended to be used on a Toro compact tool carrier.
Contents Safety Safety ....................................................................... 3 General Safety ................................................... 3 Slope Safety ....................................................... 3 Grapple Safety ................................................... 4 Maintenance and Storage Safety........................ 4 Safety and Instructional Decals .......................... 5 Product Overview .....................................................
Grapple Safety load-bearing attachment makes the rear of the machine the heavy end, and a full load-bearing attachment makes the front of the machine the heavy end. Most other attachments make the front of machine the heavy end. • For wheeled machines, use the counterweight on the platform while using the attachment. • Always close the jaws of the attachment when not in use. • Keep the attachment in the lowered position when on slopes.
Safety and Instructional Decals Product Overview Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. g030833 decal114-1281 Figure 3 114-1281 1. Upper jaw 1. Warning; crushing hazard, grapple—keep bystanders away. 3. Lower jaw 2. Tooth Specifications decal133-8061 133-8061 Note: Specifications and design are subject to change without notice. Width Length Height Weight 87.6 cm (35.
Operation CAUTION Hydraulic couplers, hydraulic lines/valves, and hydraulic fluid may be hot. If you contact hot components, you may be burned. Determine the left and right sides of the machine from the normal operating position. • Wear gloves when disconnecting the hydraulic couplers. Installing and Removing the Attachment • Allow the machine to cool before touching hydraulic components. Refer to the Operator’s Manual for the traction unit for the installation and removal procedure.
Transport Position When transporting the grapple, keep it as close to the ground as possible, no more than 15 cm (6 inches) above the ground. Tilt the attachment rearward and keep the jaws closed. g030835 Figure 5 3. g270332 You can also use this method to rip out bushes. Place the upper jaw teeth into the ground on the far side of the bush and then close the jaws around the bush and roots, ripping the bush out of the ground. Figure 7 1. No more than 15 cm (6 inches) above the ground.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Before each use or daily Before storage Maintenance Procedure • Grease the attachment (and immediately after every washing). • Check the hydraulic lines for leaks, loose fittings, kinked lines, loose mounting supports, wear, weather, and chemical deterioration. • Paint chipped surfaces. CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders.
Storage 1. Before long term storage, wash the attachment with mild detergent and water to remove dirt and grime. 2. Check and tighten all bolts, nuts, and screws. Repair or replace any damaged or worn parts. 3. Paint all scratched or bare metal surfaces. Paint is available from your Authorized Service Dealer. 4. Store the attachment in a clean, dry garage or storage area. Cover it to protect it and keep it clean.
Declaration of Incorporation Model No. 22521 Serial No. Product Description Invoice Description General Description Directive 319000001 and Up Grapple Rake, Compact Tool Carriers GRAPPLE RAKE Compact Utility Loader 2006/42/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC. We will undertake to transmit, in response to requests by national authorities, relevant information on this partly completed machinery.
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
