Form No. 3439-180 Rev B Grapple Bucket Compact Tool Carriers Model No. 22590—Serial No. 400000000 and Up Register at www.Toro.com.
This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication. WARNING CALIFORNIA Proposition 65 Warning Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Introduction g321300 Figure 1 1.
Contents Safety Safety ....................................................................... 3 General Safety ................................................... 3 Slope Safety ....................................................... 4 Attachment Safety .............................................. 4 Maintenance and Storage Safety........................ 4 Safety and Instructional Decals .......................... 5 Product Overview .....................................................
Slope Safety a safe distance between the machine and any hazard. • Operate the machine up and down slopes with • Do not remove or add attachments on a slope. the heavy end of the machine uphill. Weight distribution changes with attachments. An empty load-bearing attachment makes the rear of the machine the heavy end, and a full load-bearing attachment makes the front of the machine the heavy end. Most other attachments make the front of machine the heavy end.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal125-6110 125-6110 1. Crushing hazard—do not stand under any part of the machine. decal138-0537 138-0537 1. Warning—read the Operator’s Manual. decal133-8061 2. Entanglement hazard, grapple—keep bystanders away. 133-8061 decal144-2006 144-2006 1.
Product Overview Maximum Material Density at Capacity Specifications Width 85.6 cm (33.5 inches) Length 78.2 cm (30.8 inches) Height 53.6 cm (21.1 inches) The density of the materials moved by the bucket varies and, therefore, so does the amount of material that the bucket can carry before reaching the maximum load rating. The first 2 tables lists the density of material that can be carried, both heaped and struck (i.e., leveled off), in the bucket.
Operation Material Density Material Density (Approximate) Caliche 1250 kg/m3 (78 lb/ft3) Determine the left and right sides of the machine from the normal operating position. Clay: Natural bed 1600 kg/m3 (104 lb/ft3) Dry 1480 kg/m3 (93 lb/ft3) Wet 1660 kg/m3 (104 lb/ft3) With gravel, dry 1420 kg/m3 (89 lb/ft3) With gravel, wet 1540 kg/m3 (96 lb/ft3) Installing and Removing the Attachment Refer to the Operator’s Manual for the traction unit for the installation and removal procedure.
Bucket Operation CAUTION Hydraulic couplers, hydraulic lines/valves, and hydraulic fluid may be hot. If you contact hot components, you may be burned. • Wear gloves when disconnecting the hydraulic couplers. • Allow the machine to cool before touching hydraulic components. • Do not touch hydraulic fluid spills. With the jaws open, you can use this attachment as a standard bucket. When loading material, always have the bucket level to the ground and move forward into the material to be lifted.
Filling the Bucket Transport Position 1. Position the bucket level to the ground. 2. Drive forward and insert the bucket into the pile of material. 3. When the bucket is full, drive the machine in reverse and gently tilt the bucket rearward to decrease the lifting resistance when you lift the load. When transporting a load, keep the attachment as close to the ground as possible, no more than 15 cm (6 inches) above the ground. Tilt it rearward to keep the load level.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Before each use or daily Maintenance Procedure • Lubricate the bucket. • Check the hydraulic lines for leaks, loose fittings, kinked lines, loose mounting supports, wear, weather, and chemical deterioration. • Ensure that all fasteners are securely tightened. • Clean the areas around the bucket cylinder and mount plate pivot. • Check for wear of pins, linkages, and cutting edges.
Storage 1. Before long-term storage, wash the attachment with mild detergent and water to remove dirt and grime. 2. Check and tighten all hardware. Repair or replace any part that is damaged or worn. 3. Ensure that all of the hydraulic hose couplers are connected together to prevent contamination of the hydraulic system. 4. Paint all scratched or bare metal surfaces. Note: Paint is available from your Authorized Service Dealer. 5. Grease the pivot points; refer to Lubricating the Bucket (page 10).
Notes:
Declaration of Incorporation The Toro Company, 8111 Lyndale Avenue South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 22590 Serial No.
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
