MODEL 22610709 - 12 PECO PECO OWNERS MANUAL FOR A TORO Z-MASTER UNIT 2001 P# Q0233 REVISED 01/08/01 CONGRATULATIONS AND THANK YOU FOR BUYING THIS PECO LAWN VACUUM. Your new PECO Vac has been engineered and manufactured to PECO'S high standards for safety, quality and dependability and ease of operations.
PECO WARRANTY PeCo Limited Warranty for New Products A. WHAT IS WARRANTED? PeCo extends the following warranties to the original purchaser of each new PeCo consumer product subject to the following limitations. 1. PRODUCT WARRANTY.
PECO SAFETY Outdoor Power Equipment Institute Recommendations WARNING TO PURCHASERS OF INTERNAL COMBUSTION ENGINE EQUIPPED MACHINERY OR DEVICES IN THE STATE OF CALIFORNIA: The equipment which you have purchased does not have a spark arrester muffler. If this equipment is to be used on any forest covered and brush covered land or grass covered unimproved land in the state of California, the law requires that a spark arrester muffler be installed and be in effective working order.
PECO ASSEMBLY A STEP 1: TO FASTEN CHANNEL CLAMP (A) TO MOUNT PLATE (B) USE (4) 3/8"-16 x 1" HEX BOLTS (#K1191) AND (4) 3/8"16 FLANGE NUTS (#K1215). USE FIGURE 1-1 TO PLACE BOLTS. B HOLES FOR MOUNTING TO MOWER FIGURE 1-1 HOLES TO MOUNT CHANNEL CLAMP STEP 2: TO MOUNT MOUNT PLATE (A) TO THE MOWER FRAME USE (2) 3/8"-16 x 3" U-BOLTS (#K1118) AND (4) 3/8"-16 FLANGE NUTS (#K1215). USE FIGURE 1-1 TO PLACE BOLTS.
PECO ASSEMBLY STEP 3: A Slide Engine Mount Arm (B) into the receiver on the Mount Plate (A) and fasten by dropping in ball pin (#J0248). Place Engine/ Blower Assembly onto Engine Mount Arm (B) and fasten with (4) 5/16"-18 x 1 1/2 hex bolts (#K1157) and (4) 5/16"-18 flange nuts. Tighten nuts and bolts. B STEP 4: A The ears of the Cone (A) should fit underneath the two threaded bosses on the Blower Face (B). Secure with (2) 5/16"-18 x 2" cone bolts.
PECO PARTS LIST REF. NO. 1 2 3 4 5 6 PART NO. ******* ******* J6006 ******* E6004 ******* E4052A D4002 A0645 D1016 A0914 7 8 9 10 11 12 13 14 16 17 18 19 20 21 22 23 24 6 J6011 ******* V1054 A0023 A0913 A0907 B2250 A0917 A0780 B1941 B1926 J0316 A0021 A0022 A0236 A08221 VV2002 DESCRIPTION QTY.
PECO EXPLODED VIEW 10 9 21 22 11 7 20 19 8 12 7 18 6 22 17 16 3 5 14 3 1 2 4 13 MODEL 22610709 - 12 TORO Z-MASTER 2001 PECO 7
PECO ASSEMBLY STEP 5: Attach Base Frame (A) to Mount Plate (C) and secure by dropping in ball pin (#J0248). With hood open on the Base Frame (A) insert the 7cu. ft. Canister (B) and close C REAR VIEW OF MOWER A B D STEP 6: A B C 8 MODEL 22610709 - 12 TORO Z-MASTER Place Clamps (A) over each end of 6" Hose (B). Attach one end of hose onto Blower Housing (C). Attach free end of hose over Inlet (D).
PECO ASSEMBLY STEP 7: To mount the boot plate (A) to the boot (B) use (2) 3/8"-16 x 1" carriage bolts (K1182) and (2) 3/8"-16 flange nuts (K1178). Besure when bolting together that the head of the bolt is inside the boot. Once boot & boot plate are fastened hang boot to mower as shown. A A STEP 8: For 62" & 72" decks bolt cover plate (A) (B1811) to deck as shown, using 5/16"-18 X 1" hex bolt (K1154) and 5/16"-18 flange nut (K1178). A STEP 9: Place Clamp over each end of Lower Hose.
PECO MAINTENANCE Your Lawn Vac was designed and built to provide years of service with only minor care. Certain tasks however must be performed to keep it in good operating condition and to avoid costly repairs. This section describes and provides procedures for the necessary care of the Lawn Vac. SCHEDULED CARE CARE REQUIRED Before Each Use Check engine oil. Check all hose connections. After Each Use Clean Collector Box, hoses and engine of all grass and dirt.
PECO TROUBLE SHOOTING Diagnostic Procedures Trouble shooting procedures are provided in the chart below. To use these procedures, first locate the problem description that best describes the trouble that you have encountered. Check the possible causes one at a time in the list. Correct any problems that are found and operate the vacuum collector again to verify that you have eliminated the problem. DO NOT attempt any major repairs without first contacting your dealer.
PECO P.O BOX 1197 ARDEN, NORTH CAROLINA 28704 1-800-438-5823 OR (828) 684-1234 FAX-(828) 684-0858 E-MAIL: PECO@IOA.
