77 e Hatpin Omar. . This Owner Manual has been especially prepared for your information and guidance in the operation and care of your new Orc mower. Information on care and operation of the engine is contained in a separate manual furnished with the engine. Properly adjusted, operated and maintained, this Toto mower will respond quickly and easily to every reasonable demand and give years of reliable service.
SPECIFICATIONS ENGINE: 3% H.P., 4-cycle engine with oil pump, oil Death air cleaner, recoil starter and 5 quart gas tank. CUTTER BAR: 21" hardened high carbon steel, positive attachment with one fastener. WIDTH OF CUT: 21" HEIGHT OF CUT: moving wheels. HOUSING: No. 12 gauge stamped steel, spiral grass chamber, right hand discharge, hinged chute deflector. FRAME: Integral with housing; No.
ATTACHING THE MOWER HANDLES STEP 1. GAS TANK AND HANDLE ASSEMBLY This handle is shipped in two sections, with attaching screws contained separately in the parts bag. Place gas tank in position, then securely fasten both handle halves and gas tank bracket as shown above, STEP 2. INSTALL HANDLE TO HOUSING After handle sections have been joined together, place handle in position. Insert shoulder screw A" through handle and frame ag shown in illustration and secure with a lockout, STEP 3.
ADJUSTING HEIGHT-OF-CUT E AL KNS Graph in photo above indicates cutting heights available, To adjust, remove wheels by placing wrench on hex portion of spindle at point "A", in photo below, and removing nut "B". For normal cutting, be sure all four wheels are in the same relative hole position. For rough cutting, rear wheels can be set higher for maximum engine power. It is also advisable to move front shield up.
PREPARATION OF ENGINE BEFORE STARTING OIL AND GASOLINE have been completely removed and drained from the engine, and it is essential that the preparation instructions in this manual be followed before starting. FILL THE OIL SUMP WITH OIL First remove filler plug A", Place the engine level; be sure wheels are in the same position. Pour oil slowly to prevent air being trapped in cil sump.
STARTING INSTRUCTIONS After filling with gasoline and oil, your mower is ready for operation, The engine is controlled by the control lever on the mower handle. The manual choke is located on the engine carburetor panel, this lever are shown below. 1, STARTING POSITION (Full Forward) RECOIL START First, move the handier control lever forward to the starting position as shown in illustration No, 1. HOLD THE MOWER FIRMLY IN POSITION.
SHARPENING THE CUTTER BAR 1. To remove the cutter bar, disconnect spark plug lead wire, grasp bar as shown, and turn blade nut sharply counterclockwise, Remove anti-scalp dish, blockader and bar., CHECKING SPARK PLUG GAP This engine is equipped with a 14 mm spark plug {Use Champion J-8 or equivalent for replacement). Keep a fresh plug on hand. Clean and reset the gap at . 030 inches every 100 hours of operation. Use some graphite grease on threads ‘when replacing spark plug, 8 2.
DRAINING AND REFILLING THE OIL SUMP To avid spilling gasoline on your lawn or driveway, plan to change the oil when the gas tank and carburetor are empty. Remove cutter bar and anti-scalp dish, To facilitate drainage of oil sump, loosen filler plug “A' at front of engine, tip mower on side and remove drain plug as shown in industrialization. Place mower in normal position over shallow pan and let it drain, Change oil after first two hours of operation WHILE ENGINE IS WARM.
= o R EXTRA GIANT BAGS Additional jean bags cane purchased at nominal cost, The super size bags have three times the capacity of the regular grass clipping bag that is standard equipment. The large bags are recommended for leaves or dry litter only, Do not use for grass clippings. LAWN VAC ATTACHMENT KIT Bag your leaves--end tedious raking forever, Toto's optional Lawn Vac Attachment Kit contains 2 super size bags, bagging chute, and the necessary rods and fasteners for easy installation.
INSTALLATION OF LAWN VAC KIT (Optional Equipment) Remove wing nut "A” and lift binged deflector "B", 1 Install the cloth bag and fastener as shown above, Bag Then place discharge chute in position as shown in should he secured on the bagging chute lip. above illustration, Replace wing nut "A” securely on stud under the hinged deflector, The 21" Whirlwind Nevi-Duty mower with the bagging 10 attachment properly installed is illustrated above.
ENGINE No. LAVAL-3410 PARTS LIST Ref. No. Ref. No. No, | Part No. ‘Description Used| No., | part No. Description Used 1 30613 |Cylinder Says. 47 30579 | Head, Cylinder 1 {Incl. Nos. 26073 | Washer 5 2 26727 | Pin, Dowel 2 49 6021 Resew 5 3 27183 |Washer, Fiber 2 50 6023 Screw 3 4 1*20183 |[Seal, Oil 1 51 21943 | Plug, Spark 5 29314 |valve, Intake (Standard) 1 (Champion J-8 or equiv.
ENGINE #LAVAL-3410 PARTS LIST (Continued) Ref. No. Ref, No. No. [Part No, Description Used] No. | Part No.
Ref. No. Ref. No. No. | Bart No. Description Used, No. | Part No.
CARBURETOR No. 630937 Drawing No. 8085-18 Ref. No. Ref. No. No. | Part No. Description Used No. | Part No. Description Used 1 { 30816 |Shaft & Lever, Throttle 1 16 27136 | Stem & Gasket Says.
2 The Manufacturer warrants each new piece of equipment sold to be free of defects in material and workmanship. For one year {rom the purchase date of consumer line equipment or 45 days if sold for commercial use, Tore Manufacturing Corporation will repair or replace for the original purchaser, free of charge, through any Authorized Service Dealer, any part or parts found at our factory in Minneapolis, Minnesota, to be defective under normal use and service.