Service Manual
Table Of Contents
- 1 - safety info_21in Aerator 4 web.pdf
- 2 - specs n maint_21in Aerator 4 web.pdf
- Specifications 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Specifications 2014 models (Serial 314000001 & up)
- Handle Adjustment (Serial 314000001 & up)
- Adjusting the Coring Depth (All Models)
- Adjusting the Tine Control Lever 2014 models (Serial 314000001 & up)
- Lift Drop Cable Adjustment 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Recommended Maintenance Schedule
- Accessing the Tines & Tipping the Machine
- Greasing the Tine Shaft Bearings
- Lubricating & Checking the Drive Chains & Sprockets
- Servicing the Air Cleaner
- Changing the Engine Oil
- Changing the Oil Filter
- Servicing the Spark Plug
- Check the Spark Arrester (if equipped)
- Emptying the Fuel Tank and Cleaning the Fuel Filter
- Replacing the Fuel Filter
- Checking the Tire Pressure
- Adjusting the Tension of Tine Drive Chains
- Checking the Hydrostatic Drive Belt
- Adjusting the Machine Ground Speed 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Adjusting the Self-Propel Drive 2014 models (Serial 314000001 & up)
- Changing the Hydraulic Transmission Fluid
- Checking/Replacing Tines
- Troubleshooting
- 3 - chassis_21in Aerator 4 web.pdf
- Handle Subsystem – 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Handle Subsystem – 2014 (Serial 314000001 & up)
- Engine Frame Subsystem – 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Engine Frame Subsystem – 2014 (Serial 314000001 & up)
- Height Linkage
- Subsystem – Height Linkage - 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Subsystem – Height Linkage - 2014 (Serial 314000001 & up)
- Drive Cable Removal & Installation
- Tine Control Cable Removal & Installation - Serial 312000001 & up, Serial 313000001 & up
- Adjusting Handle - Serial 314000001 & up
- Adjusting the Tine Control Lever - Serial 314000001 & up
- Replacing Pivot Shaft - Serial 312000001 & up, Serial 313000001 & up
- Replacing Pivot Shaft - Serial 314000001 & up
- Replacing the Front Drive Axle - All Models
- 4 - hydr n eng mount_21in Aerator 4 web.pdf
- 5 - tine system_21in Aerator 4 web.pdf
SPECIFICATIONS & MAINTENANCE
2-7
Toro 21” Aerator Service Manual
2
Lift Drop Cable Adjustment 2012-13
models (Serial 312000001 & up, Serial
313000001 & up)
1. Adjust jam nut all the way to the end so no threads
are showing. Adjust the yoke as far onto the rod as
possible and re-tighten the jam against the yoke (A -
Fig. 009).
2. Adjust the Cable Housing Anchor Nuts so there are
an equal number of threads on each end and re-
tighten (B - Fig. 010).
3. Adjust the lower nut all the way to the end so that
one thread is showing at most. Tighten the internal
nut to secure the cable to the bracket (C - Fig. 012).
4. Adjust jam nut all the way to the end so no threads
are showing. Adjust the yoke as far onto the rod as
possible and re-tighten the jam against the yoke (D -
Fig. 013).
Fig. 008 DSCN-0016a
Fig. 009 011a
Fig. 012 DSCN-0032
Fig. 010 DSCN-0019a
Fig. 013 DSCN-0029
Fig. 011 DSCN-0024
A
B
A B
C D
C
D