Service Manual
Table Of Contents
- 1 - safety info_21in Aerator 4 web.pdf
- 2 - specs n maint_21in Aerator 4 web.pdf
- Specifications 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Specifications 2014 models (Serial 314000001 & up)
- Handle Adjustment (Serial 314000001 & up)
- Adjusting the Coring Depth (All Models)
- Adjusting the Tine Control Lever 2014 models (Serial 314000001 & up)
- Lift Drop Cable Adjustment 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Recommended Maintenance Schedule
- Accessing the Tines & Tipping the Machine
- Greasing the Tine Shaft Bearings
- Lubricating & Checking the Drive Chains & Sprockets
- Servicing the Air Cleaner
- Changing the Engine Oil
- Changing the Oil Filter
- Servicing the Spark Plug
- Check the Spark Arrester (if equipped)
- Emptying the Fuel Tank and Cleaning the Fuel Filter
- Replacing the Fuel Filter
- Checking the Tire Pressure
- Adjusting the Tension of Tine Drive Chains
- Checking the Hydrostatic Drive Belt
- Adjusting the Machine Ground Speed 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Adjusting the Self-Propel Drive 2014 models (Serial 314000001 & up)
- Changing the Hydraulic Transmission Fluid
- Checking/Replacing Tines
- Troubleshooting
- 3 - chassis_21in Aerator 4 web.pdf
- Handle Subsystem – 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Handle Subsystem – 2014 (Serial 314000001 & up)
- Engine Frame Subsystem – 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Engine Frame Subsystem – 2014 (Serial 314000001 & up)
- Height Linkage
- Subsystem – Height Linkage - 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Subsystem – Height Linkage - 2014 (Serial 314000001 & up)
- Drive Cable Removal & Installation
- Tine Control Cable Removal & Installation - Serial 312000001 & up, Serial 313000001 & up
- Adjusting Handle - Serial 314000001 & up
- Adjusting the Tine Control Lever - Serial 314000001 & up
- Replacing Pivot Shaft - Serial 312000001 & up, Serial 313000001 & up
- Replacing Pivot Shaft - Serial 314000001 & up
- Replacing the Front Drive Axle - All Models
- 4 - hydr n eng mount_21in Aerator 4 web.pdf
- 5 - tine system_21in Aerator 4 web.pdf
SPECIFICATIONS & MAINTENANCE
2-18
Toro 21” Aerator Service Manual
2
B. Pull down on the idler sprocket until the slack is
taken out of the chain.
C. Tighten the idler sprocket nut and torque it to 30
ft-lbs. (40.6 Nm).
4. Repeat step 3 to test the chain tension and tighten it
as needed.
5. Repeat this procedure for the other tine drive chain.
A. Loosen the nut securing the idler sprocket of the
chain you are tensioning (Fig. 029).
Fig. 029 g. 32 G023852
A. Idler sprocket B. Nut
A
B
Checking the Hydrostatic Drive Belt
1. Raise the tines, stop the machine, stop the engine,
and disconnect the spark plug wire.
2. Raise the front of the machine to gain access to the
pump drive belt and block it in place.
CAUTION
If you do not securely block the up the front
of the machine the machine could fall on you
during service injuring you.
Ensure that you place a jack stand or block
under the front of the machine to hold it up
securely.
Important: Do not raise the rear of the machine.
Raising the rear of the machine will cause
the engine to ood and the air cleaner to be
fouled with gasoline.
! !