Service Manual
Table Of Contents
- 1 - safety info_21in Aerator 4 web.pdf
- 2 - specs n maint_21in Aerator 4 web.pdf
- Specifications 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Specifications 2014 models (Serial 314000001 & up)
- Handle Adjustment (Serial 314000001 & up)
- Adjusting the Coring Depth (All Models)
- Adjusting the Tine Control Lever 2014 models (Serial 314000001 & up)
- Lift Drop Cable Adjustment 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Recommended Maintenance Schedule
- Accessing the Tines & Tipping the Machine
- Greasing the Tine Shaft Bearings
- Lubricating & Checking the Drive Chains & Sprockets
- Servicing the Air Cleaner
- Changing the Engine Oil
- Changing the Oil Filter
- Servicing the Spark Plug
- Check the Spark Arrester (if equipped)
- Emptying the Fuel Tank and Cleaning the Fuel Filter
- Replacing the Fuel Filter
- Checking the Tire Pressure
- Adjusting the Tension of Tine Drive Chains
- Checking the Hydrostatic Drive Belt
- Adjusting the Machine Ground Speed 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Adjusting the Self-Propel Drive 2014 models (Serial 314000001 & up)
- Changing the Hydraulic Transmission Fluid
- Checking/Replacing Tines
- Troubleshooting
- 3 - chassis_21in Aerator 4 web.pdf
- Handle Subsystem – 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Handle Subsystem – 2014 (Serial 314000001 & up)
- Engine Frame Subsystem – 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Engine Frame Subsystem – 2014 (Serial 314000001 & up)
- Height Linkage
- Subsystem – Height Linkage - 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Subsystem – Height Linkage - 2014 (Serial 314000001 & up)
- Drive Cable Removal & Installation
- Tine Control Cable Removal & Installation - Serial 312000001 & up, Serial 313000001 & up
- Adjusting Handle - Serial 314000001 & up
- Adjusting the Tine Control Lever - Serial 314000001 & up
- Replacing Pivot Shaft - Serial 312000001 & up, Serial 313000001 & up
- Replacing Pivot Shaft - Serial 314000001 & up
- Replacing the Front Drive Axle - All Models
- 4 - hydr n eng mount_21in Aerator 4 web.pdf
- 5 - tine system_21in Aerator 4 web.pdf
SPECIFICATIONS & MAINTENANCE
2-23
Toro 21” Aerator Service Manual
2
Troubleshooting
Problem Possible Cause Corrective Action
Engine will not start.
1. The throttle lever is in the Off
position.
2. The spark plug is disconnected.
3. The fuel is turned off.
4. The traction lever is not in neutral.
1. Move the throttle lever to the
Choke position.
2. Connect the spark plug.
3. Open the fuel valve.
4. Release the traction lever so it
returns to neutral.
The machine vibrates abnormally. 1. Loose bolts and/or broken parts.
1. Stop the machine and engine
immediately. Replace any broken
or missing parts.
The machine will not pull itself up
hills.
1. The drive belt to the hydrostatic
pump is loose.
1. Check and tighten the pump drive
belt.
The front wheels move but the tines
do not.
1. A chain or drive sprocket is
broken.
1. Replace the broken chain or
sprocket.
The engine smokes when starting. 1. The engine was tipped forward.
1. Check the air cleaner and
replace it if it is fouled. Always tip
the machine back when servicing.
The engine is hard to start after
transporting it.
1. The fuel valve was not closed
before transport and the engine is
ooded.
1. Always close the fuel valve before
transporting the machine.
The ground speed is slow.
1. The drive or pump belt is worn,
loose, or broken.
2. The engine idle is not set properly.
3. The chains are not properly
tensioned.
1. Check and tighten the pump drive
belt, or change the belt.
2. Contact an Authorized Service
Dealer.
3. Adjust the tine drive chain.
The tines drop out of transport when
the handle is folded over.
1. Tine-control lever is out of
adjustment.
1. Adjust the tine-control lever.