Service Manual
Table Of Contents
- 1 - safety info_21in Aerator 4 web.pdf
- 2 - specs n maint_21in Aerator 4 web.pdf
- Specifications 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Specifications 2014 models (Serial 314000001 & up)
- Handle Adjustment (Serial 314000001 & up)
- Adjusting the Coring Depth (All Models)
- Adjusting the Tine Control Lever 2014 models (Serial 314000001 & up)
- Lift Drop Cable Adjustment 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Recommended Maintenance Schedule
- Accessing the Tines & Tipping the Machine
- Greasing the Tine Shaft Bearings
- Lubricating & Checking the Drive Chains & Sprockets
- Servicing the Air Cleaner
- Changing the Engine Oil
- Changing the Oil Filter
- Servicing the Spark Plug
- Check the Spark Arrester (if equipped)
- Emptying the Fuel Tank and Cleaning the Fuel Filter
- Replacing the Fuel Filter
- Checking the Tire Pressure
- Adjusting the Tension of Tine Drive Chains
- Checking the Hydrostatic Drive Belt
- Adjusting the Machine Ground Speed 2012-13 models (Serial 312000001 & up, Serial 313000001 & up)
- Adjusting the Self-Propel Drive 2014 models (Serial 314000001 & up)
- Changing the Hydraulic Transmission Fluid
- Checking/Replacing Tines
- Troubleshooting
- 3 - chassis_21in Aerator 4 web.pdf
- Handle Subsystem – 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Handle Subsystem – 2014 (Serial 314000001 & up)
- Engine Frame Subsystem – 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Engine Frame Subsystem – 2014 (Serial 314000001 & up)
- Height Linkage
- Subsystem – Height Linkage - 2012 (Serial 312000001 & up), 2013 (Serial 313000001 & up)
- Subsystem – Height Linkage - 2014 (Serial 314000001 & up)
- Drive Cable Removal & Installation
- Tine Control Cable Removal & Installation - Serial 312000001 & up, Serial 313000001 & up
- Adjusting Handle - Serial 314000001 & up
- Adjusting the Tine Control Lever - Serial 314000001 & up
- Replacing Pivot Shaft - Serial 312000001 & up, Serial 313000001 & up
- Replacing Pivot Shaft - Serial 314000001 & up
- Replacing the Front Drive Axle - All Models
- 4 - hydr n eng mount_21in Aerator 4 web.pdf
- 5 - tine system_21in Aerator 4 web.pdf
HYDRAULICS & ENGINE MOUNTING
4-2
Toro 21” Aerator Service Manual
4
5. Disconnect the self-propel drive bail cable from the
transmission (Fig. 095).
Fig. 094 1-1a
Fig. 095 1a
6. Loosen the nut on the idler pulley to make the belt
go slack (Fig. 096).
Fig. 096 2a
Transmission Replacement
Transmission Removal
1. Raise the tines, stop the machine, stop the engine,
and disconnect the spark plug wire.
2. Drain the fuel from the fuel tank. Dispose of fuel in
an approved container.
3. Slide the oval locking rings on the handle upward,
and fold the handle towards the engine.
4. Slowly lift the front of the machine until the back of
the machine and weight pockets are resting on the
ground. Stabilize the machine with an overhead
hoist (Fig. 094).
Note: Using two people or an overhead hoist to lift
the machine will make this easier.