Installation Instructions

ManualsBrandsToro ManualsUtility VehicleToro 23813

FormNo.3398-624RevA

DirtandRockStakes

2024and4045DirectionalDrill

ModelNo.23812

ModelNo.23812E

ModelNo.23813

ModelNo.23813E

ModelNo.23814

ModelNo.23814E

ModelNo.23815

ModelNo.23815E

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

2024Dirtstakes2

2024Rockstakes2

Coupler

Stakepin

O-ring

Locknut(M12)

Bolt(M12-13/4x80mm)

Greasetting

Stakeguide

Guidering

Bolt(M8-11/4x20mm)

Installthestakesonthe2024directionaldrill.

RockorDirtstake2

Guidering

Stakeguide

Bolts(M10-11/2x25mm)

Installthestakesforthe4045directionaldrill.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3398-624*A

Summary of content (4 pages)

PAGE 1
Form No. 3398-624 Rev A Dirt and Rock Stakes 2024 and 4045 Directional Drill Model No. 23812 Model No. 23812E Model No. 23813 Model No. 23813E Model No. 23814 Model No. 23814E Model No. 23815 Model No. 23815E Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Installing the Stakes on the 2024 Directional Drill 7. Torque the bolts to 127 to 155 N-m (94 to 114 ft-lb). 8. Pump grease into the fittings until grease begins to ooze out of the bearings (approximately 3 pumps) and wipe up any excess grease. Preparing the Machine and Installing the Coupler Installing the Dirt Stakes on the 2024 Directional Drill Note: Having 2 people or a lifting mechanism makes it easier to install the stakes. 1. Position the thrust frame 25.
PAGE 3
Installing the Rock Stakes on the 2024 Directional Drill Installing the Stakes on the 4045 Directional Drill 1. Secure the stake guide onto the guide ring using the 8 bolts (M8) (Box A of Figure 4). Preparing the Machine and Removing the Current Stakes Note: Having 2 people or a lifting mechanism makes it easier to install the stakes. 1. Position the thrust frame 25.4 cm (12 inches) off the ground, with the stakes in the up position. 2. Turn off the engine and the battery disconnect switch. 3.
PAGE 4
Installing the Rock Stakes on the 4045 Directional Drill Have 2 people perform this procedure. 1. Slide the stake guide over the top of the rock stake and place the stake on the machine as shown in Figure 6. Note: Have 1 person hold the stake in place while the other person continues this procedure. Figure 8 1. Stake guide 4. Torque the M10 bolts to 73 to 89 N-m (54 to 66 ft-lb). 5. Secure the stake to the motor as shown in Figure 5. 6. If your machine has a cage, close and latch the cage door.