Software Guide

ManualsBrandsToro ManualsUtility VehicleToro 23823A

FormNo.3416-942RevA

4045DirectionalDrillwithCab

SoftwareVersionsA–L

ModelNo.23823/A/C/TE/W—SerialNo.315000001andUp

ModelNo.23825/A/C/TE/W—SerialNo.315000001andUp

SoftwareGuide

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorT oroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.

YoumaycontactTorodirectlyatwww.T oro.com

forproductsafetyandoperationtrainingmaterials,

accessoryinformation,helpndingadealer,orto

registeryourproduct.

MainOperatingScreen

Toaccessthisscreen,pushbutton4orthedown

arrowontheMachineInformationScreen(page6).

Themainoperatingscreendisplaystheengine-speed

(rpm)gauge,thefuel-quantitygauge,the

engine-temperaturegauge,thepipe-rowselector,

thrustcontrol,andhorsepowercontrol(Figure1).

Thelow-fuelindicatorlightsuponthemain-operating

screenwhenthemachineisrunninglowonfuel

(Figure1).

Pushbutton3toselectthethrustcontrol(Figure1).

Pushbutton4toselectthehorsepowercontrol(Figure

1).

Pushbutton7tosoundthehorn(Figure1).

Pushbutton8forthepipe-rowselector(Figure1).

Note:Thehornoption(button7)isonlyforsoftware

versionsKandup.

g029896

Figure1

MainOperatingScreen

1.Fuelgauge5.Horncontrol

2.Engine-speed(rpm)gauge

6.Thrustcontrol

3.Coolant-temperature

gauge

7.Horsepowercontrol

4.Pipe-rowselector

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3416-942*A

Summary of content (12 pages)

PAGE 1
Form No. 3416-942 Rev A 4045 Directional Drill with Cab Software Versions A–L Model No. 23823/A/C/TE/W—Serial No. 315000001 and Up Model No. 23825/A/C/TE/W—Serial No. 315000001 and Up Software Guide Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
PAGE 2
Main Drill Functions Displayed in Pressure Screen Main Drill Functions Displayed in Torque Screen To access this screen, push the down arrow on the Main Drill Functions Displayed in Pressure Screen (page 2). To access this screen, push the down-arrow button on the Main Operating Screen (page 1). This screen provides measurements on rotary torque in ft-lbs, drilling-fluid pressure in psi, carriage force in lbs, and drilling-fluid flow rate in gpm (Figure 3).
PAGE 3
Drill Rotation Speed Screen Thrust Control Screen To access this screen, hold the OK button on the Main Operating Screen (page 1). This screen allows the user to increase or decrease the thrust output of the machine. This screen allows the user to increase or decrease the rotation speed of the drill. To access this screen, push button 3 on the Main Operating Screen (page 1) or on the Main Drill Functions Displayed in Pressure Screen (page 2).
PAGE 4
Horsepower Control Screen Pipe Row Selector Screen To access this screen, push button 4 on the Main Operating Screen (page 1). This screen allows you to select the row of pipe(s) that you want to use. The horsepower control sets the maximum engine load to prevent stalling under heavy loads regardless of engine RPM. To access this screen, push button 8 on the Main Operating Screen (page 1).
PAGE 5
Main Selection Screen Control Select Screen To access this screen, push the down arrow on the Main Drill Functions Displayed in Torque Screen (page 2). To access this screen, push the OK button from the Main Selection Screen (page 5).
PAGE 6
Machine Information Screen Lubrication and Maintenance Screens This screen contains the following information: To access this screen, push button 2 on the Main Selection Screen (page 5). • The machine model and serial number (Figure 10). These screens provide the user with the daily maintenance schedules and intervals shown below. • The number of engine hours for the machine (Figure 10). Note: Push the ESC button to exit this screen.
PAGE 7
Error Codes Screen To access this screen, push button 3 on the Main Selection Screen (page 5). This screen displays the number of drill errors and engine errors that have occurred. If more than 1 drill or engine error is shown on the screen, push button 5 to see the next drilling error, button 7 to see the next engine error, or button 8 to see the previous engine error (Figure 16). Note: If there are no drilling errors or engine errors, push the OK button to exit this screen (Figure 16).
PAGE 8
Loader Calibration Screen Loader Cam Calibration Screen To access this screen, push button 6 on the Main Selection Screen (page 5). To access this screen, push button 1 on the Loader Calibration Screen (page 8). This screen allows you to calibrate the loader cam or to calibrate the loader arm. This screen allows the user to set the row positions for the pipe holder. This screen also allows you to adjust the cam-stop positions, ensuring that the cam is in line with the pipe row.
PAGE 9
Loader Arm Calibration Screen Clear Service Reminder Screen To access this screen, push button 2 on the Loader Calibration Screen (page 8). To access this screen, push button 7 on the Main Selection Screen (page 5). This screen allows the user to set the loader arm to the In position (fully inward toward the machine), or to the Home position (fully out away from the machine).
PAGE 10
Informational Screens Auxiliary Activations Screen Push the 1 and 5 button simultaneously to access these screens. The auxiliary-activations screen (Figure 23) provides the following information: • On and Off indicators for clamps, wrench breakout Push the up and down arrows to scroll through these screens. (for upper wrench), TJC applicator, setup, pipe rotation, pipe arms, pipe grip, and pipe elevator Push the ESC button to return to the Main Operating Screen (page 1).
PAGE 11
Track Drive Information Screen Machine Information Screen The track drive information screen (Figure 27) provides the following information: The machine information screen (Figure 27) provides the following output information for: • Output for left forward, left reverse, right forward, • Fuel rate and right reverse movements of the track drive • Oil pressure • Front-Neutral-Reverse (FNR) and steer joystick • Voltage output • Engine speed • On and Off indicators for setup and seat switch • Fuel
PAGE 12
Informational and Warning Icons Stake Down Cage Warning Icon (CE models only) Software Versions K and up Only This icon (Figure 30) will display if the stake down cage door is not closed. Collision Condition Indicator Screen The carriage stops and the icon displays when there is a collision condition between the drill head and the pipe/arm loader (Figure 28). g223941 Figure 30 g029983 Figure 28 1.