Software Guide

ManualsBrandsToro ManualsUtility VehicleToro 23898

FormNo.3419-198RevA

4045and4050DirectionalDrill

SoftwareVersionsA–C

ModelNo.23823/A/C/TE/W—SerialNo.315000001andUp

ModelNo.23825/A/C/TE/W—SerialNo.315000001andUp

ModelNo.23898—SerialNo.400000000andUp

ModelNo.23899—SerialNo.400000000andUp

SoftwareGuide

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorT oroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.

YoumaycontactTorodirectlyatwww.T oro.com

forproductsafetyandoperationtrainingmaterials,

accessoryinformation,helpndingadealer,orto

registeryourproduct.

MainInformationScreen

Thisistherstscreenthatappearsaftertheinitial

splashscreen.T onavigatebetweenscreens,usethe

leftandrightarrows.

g214633

Figure1

1.Drillspeed(rpm)4.Enginespeed(rpm)

2.Rotarytorque

5.Drilling-uidowrate

3.Thrustforce6.Drilling-uid/Air-hammer

pressure

g214634

Figure2

1.Pipefunctions

5.Enginetemperaturegauge

2.Fuelgauge6.Enginedroop

3.Limitsettingoptions7.Horn

4.Selectpiperow8.Thrustforce,drillspeed

(rpm),orrotarytorque

adjustment

GototheMudorAirHammerSelectionScreen(page

12)toswitchbetweenmudpressureandairhammer

functions.

Pushbutton1toswitchbetweenthepipefunctions

pullpipe,pushpipe,andneutral.

Pushbutton5toswitchbetweenthrustforce,drill

speed(rpm),androtarytorquelimits.

Usetheupanddownarrowstosetthelimitsfor

maximumdrillspeed(rpm),rotarytorque,andthrust

force.

•Thrustforce:Changethethrustforcelimitby

pushing6or7.

•Drillspeed(rpm):Changethedrillspeedrpmlimit

bypushing6or7.

•Rotarytorque:Changetherotarytorquelimitforce

bypushing6or7.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3419-198*A

Summary of content (16 pages)

PAGE 1
Form No. 3419-198 Rev A 4045 and 4050 Directional Drill Software Versions A–C Model No. 23823/A/C/TE/W—Serial No. 315000001 and Up Model No. 23825/A/C/TE/W—Serial No. 315000001 and Up Model No. 23898—Serial No. 400000000 and Up Model No. 23899—Serial No. 400000000 and Up Software Guide Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
PAGE 2
Pulling Pipe in SmartTouch Mode Start the SmartTouch mode with the cam assembly in the home position (row 4 of the pipe box). Important: Ensure that you hold the lower section of the cam rocker switch, on the left joystick, completely down until the action is complete in each step (Figure 5). g213150 Figure 3 1. Pull pipe 4. Thrust force 2. Push pipe 5. Drill speed (rpm) 3.
PAGE 3
2. Push buttons 2 and 3 to select the row where you want to place the pipe (Figure 7). g232381 Figure 7 1. Pull pipe 3. 2. Select pipe row Hold the lower section of the rocker switch (Figure 9) until the following 3 things happen (Figure 10): A. The cam assembly rotates toward the operator station. B. The elevator lowers. C. The loader arms rotate to the drill pipe.
PAGE 4
. Release the rocker switch to proceed to the next step in the sequence (Figure 11). 7. Hold the lower section of the rocker switch (Figure 15) until the arms rotate with the pipe back to the home position and the grippers open as the pipe enters the cam assembly pocket (Figure 16). g231713 Figure 11 5. 6. Break the pipe connection; refer to Removing Drill Pipes in the Operator’s Manual.
PAGE 5
8. Release the rocker switch to proceed to the next step in the sequence (Figure 17). 10. Release the rocker switch to proceed to the next step in the sequence (Figure 20). g231715 g231716 Figure 17 9. Figure 20 Hold the lower section of the rocker switch (Figure 18) until the cam assembly rotates to the selected row under the pipe box (Figure 19). 11.
PAGE 6
Pushing Pipe in SmartTouch Mode Start the SmartTouch mode with the cam assembly in the home position (row 4 of the pipe box). Important: Ensure that you hold the lower section of the cam rocker switch, on the left joystick, completely down until the action is complete in each step (Figure 23). g232387 Figure 25 1. Push pipe 3. g210060 Figure 23 2.
PAGE 7
4. Release the rocker switch to proceed to the next step in the sequence (Figure 29). 6. Release the rocker switch to proceed to the next step in the sequence (Figure 32). g231718 g231719 Figure 29 5. Figure 32 Hold the lower section of the rocker switch (Figure 30) until the cam assembly fully rotates forward to the rack and the elevators lift the remaining pipe into the pipe box (Figure 31). 7.
PAGE 8
. Release the rocker switch to proceed to the next step in the sequence (Figure 35). 11. Hold the lower section of the rocker switch (Figure 39) until the loader arms rotate back and the cam assembly returns to the home position (row 4) (Figure 40). g231720 Figure 35 9. Make the pipe connection; refer to Adding Drill Pipes in the Operator’s Manual. 10. Hold the lower button on the joystick (Figure 36) to release the pipe (Figure 37) and release the button.
PAGE 9
Hours Screen Options Lubrication and Maintenance Screens Machine Hours Screen To access this screen, push button 3 on the Hours screen. To access this screen, push button 1 on the Hours screen. These screens provide the user with the daily maintenance schedules in the increments listed below. This screen shows the operating hours of the machine. You cannot change Machine 1 but you can reset Machine 2.
PAGE 10
Settings Screen Options Carriage Settings Screen Push button 1 on the Settings screen. Use this screen to change the carriage settings. Use the up and down arrows to rotate between push pipe, pull pipe, and neutral. Push the OK button to turn SmartTouch™ on and off. g034779 Figure 45 g233212 Figure 48 Control Mode Screen Push button 2 on the Settings screen. Use this screen to select between the 2 joystick control options. Push the up and down arrows to to switch between Mode I and Mode II.
PAGE 11
Parameters Options Screen Screen Settings Push button 3 on the Settings screen. The pin number to change the parameters is 73236531. Push button 6 on the Settings screen to switch between zoom delay, brightness, and day or night mode. Use the up and down arrows to adjust the parameters. Push the down arrow to scroll to the maintenance options screen to reset the maintenance interval. Enter pin number 12356. The Main Drilling Screen zooms into the drilling functions.
PAGE 12
Mud or Air Hammer Selection Screen • The rotary voltage ranges from 0.0 to 8.5 V and can be present for either make (upper icon) or break (lower icon) as the selected rotary joystick is moved. Push button 8 on the Settings screen to access this screen. Use the up and down arrows to switch been mud and air hammer. • The carriage indicates a voltage range from 0.0 to 10.0 V in the joystick selected direction for thrust or pullback. This updates the display on the home screen (Figure 1).
PAGE 13
• If the engine is shut off, the voltage is measured • or lower indicates either sensor failure or incorrect calibration. by the Toro controller. If the engine is running, the voltage is supplied by engine controller. Auxiliary I/O Screen Engine temperature icon: displays the engine coolant temperature measured at the reservior. The temperature drops to 40°F when the engine is shut off. To access this screen push button 5 on the I/O screen.
PAGE 14
Seat switch icon: shows an arrow out when the operator seat is empty; the switch shows a figure icon when you are in the operator seat. Travel Pendant I/O Screen • Shows the seat with an error when the operator The travel pendant screen shows the voltage and position of the joystick located on the pendant. To access this screen push button 7 on the I/O screen.
PAGE 15
Engine Errors Screen Carriage Crash Warning Icon To access this screen push button 2 on the Errors and Machine Information screen. The carriage crash warning screen (Figure 64) appears if the following occurs: This screen displays any engine errors. • The carriage is in the drill area and you try to Use the up and down arrows to scroll through the errors. Contact your Authorized Service Dealer for codes that cannot be cleared.
PAGE 16
Stake Down Cage Warning Icon (CE models only) This icon (Figure 67) displays if the stake down cage door is not closed.