Software Guide

ManualsBrandsToro ManualsUtility VehicleToro 23898

FormNo.3398-121RevA

4050DirectionalDrill

ModelNo.23898—SerialNo.315000001andUp

ModelNo.23899—SerialNo.315000001andUp

SoftwareGuide

Readthisinformationcarefullytolearnhowtooperateandmaintainyourproductproperlyandtoavoidinjuryandproduct

damage.Youareresponsibleforoperatingtheproductproperlyandsafely.

Wheneveryouneedservice,genuineToroparts,oradditionalinformation,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersofyourproductready.

YoumaycontactTorodirectlyatwww.Toro.comforproductsafetyandoperationtrainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Monitor

HomeScreenOptions

MainInformationScreen

Thisistherstscreenthatappearsaftertheinitialsplash

screen.Tonavigatebetweenscreensusetheleftandright

arrows.

Figure1

1.Pipefunctions

8.Enginetemperaturegauge

2.Fuelgauge

9.Enginespeed(rpm)

3.Drillspeed(rpm)

10.Engineload

4.Rotarytorque

11.Mudowrate(gallonsper

minute)

5.Thrustforce

12.Mudpressure

6.Rotateoptions13.Horn

7.Selectpiperow14.Thrustforce,drillspeed

(rpm),orRotarytorque

adjustment

Pushnumber1toswitchbetweenthepipefunctions:pull

pipe,pushpipe,neutral.

Pushnumber5toswitchbetweenthrustforce,drillspeed

(rpm),androtarytorque.

Usetheupanddownarrowstosetthelimitsformaximum

drillspeed(rpm),rotarytorque,andthrustforce.

•Thrustforce:changethethrustforcebypushing6or7.

•Drillspeed(rpm):changethethrustforcebypushing

6or7.

•Rotarytorque:changethethrustforcebypushing6or7.

Figure2

1.Pullpipe

4.Thrustforce

2.Pushpipe

5.Drillspeed(rpm)

3.Rotarytorque

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3398-121*A

Summary of content (8 pages)

PAGE 1
Form No. 3398-121 Rev A 4050 Directional Drill Model No. 23898—Serial No. 315000001 and Up Model No. 23899—Serial No. 315000001 and Up Software Guide Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
PAGE 2
Hours Screen Options Lubrication and Maintenance Screens Machine Hours Screen To access this screen, press button number 3 on the Hours screen. To access this screen press button 1 on the Hours screen. These screens provide the user with the daily maintenance schedules and the 50-hour, 250-hour, 500-hour, and 1,000-hour increments. This screen shows the operating hours of the machine. Machine 1 cannot be changed. Machine 2 can be reset.
PAGE 3
Settings Screen Options Carriage Settings Screen Push number 1 on the Settings screen. Use this screen to change the carriage settings. Use the up and down arrows to rotate between: push pipe, pull pipe, and neutral. Figure 7 Figure 10 Figure 8 Push Pipe • Rotate Cam to Load The cam stops at the assigned row position. Lower the elevator and rotate the cam and pipe to the load position. Actuate the pipe loader to bring the pipe toward the rack.
PAGE 4
Pull Pipe Parameters Options Screen • Rotate Cam to Load Push number 3 on the Settings screen. The cam moves from the home position to the load position without stopping at the selected row. Extend the load arm and grip the pipe prior to completion of the pipe breaking from the drill string and pipe head. Retract the load arm and lower the elevator. The grips will automatically open as the pipe loader passes through the grip point of the cam. The pin number to change the parameters is 73236531.
PAGE 5
I/O Screens Screen Settings Screen Push number 6 on the Settings screen to switch between zoom delay, brightness, and day or night mode. Use the up and down arrows to adjust the parameters. Joystick I/O Screen Push number 1 on the I/O screen to rotate between the Drill and Setup options. The icon turns green when the associated function is actuated. The Main Drilling Screen zooms into the drilling functions. These settings adjust the delay on how long it takes to zoom.
PAGE 6
Engine I/O Screen Cam Arm I/O Screen To access this screen push number 2 on the I/O screen. To access this screen push number 3 on the I/O screen. This screen displays engine information. Use this screen to adjust the cam and pipe loader calibration options. Figure 17 1. Engine speed (rpm) 5. Air filter indicator 2. Engine oil pressure 6. Hydraulic oil filter 3. Battery voltage 7. Engine load 4. Engine temperature 8.
PAGE 7
Auxiliary I/O Screen Controller I/O Screen To access this screen push number 5 on the I/O screen. To access this screen push number 6 on the I/O screen. All icons change from black to green when the associated functions are operated. Figure 20 Figure 19 1. Raise/Lower elevator 2. Breakout wrench 5. Loader arm 6. Rotate pipe cam 3. Upper or lower wrench 7. TJC grease 1. Seat switch 4. Carriage crash warning 2. Exit side lockout 5. Mud pump status 3. Pedestrian gate 6.
PAGE 8
Travel Pendant I/O Screen Engine Errors Screen To access this screen push number 7 on the I/O screen. To access this screen push number 2 on the Errors and Machine Information screen. The travel pendant screen shows the voltage and position of the joystick located on the pendant. This screen displays any engine errors. Figure 21 Figure 23 The red dot will be in the center of the target and the FNR (forward, neutral, reverse) and Steer voltage shows 2.5 V prior to allowing the drill to move.