Installation Instructions

ManualsBrandsToro ManualsTrenchersToro 25201E

FormNo.3407-352RevA

ComboforDirectDriveTrencherandP85Plow

RT600TractionUnit

ModelNo.25201

ModelNo.25201E

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocatednear

anyareaofpotentialdanger.Replaceany

decalthatisdamagedorlost.

133-5056

1.Important—readtheOperator’sManualtocompletethe

installationcorrectly.

131-2682

1.Raiseorlowerthe

attachments.

3.Plow

2.Trencher

125-6139

1.Liftpointandtie-downpoint

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3407-352*A

Summary of content (12 pages)

PAGE 1
Form No. 3407-352 Rev A Combo for Direct Drive Trencher and P85 Plow RT600 Traction Unit Model No. 25201 Model No. 25201E Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. 131-2682 Safety and Instructional Decals 1. Raise or lower the attachments. 2. Trencher 3.
PAGE 2
Preparing the Machine Ensure that the lifting equipment has a lifting capacity of at least 405 kg (893 lb). D. 1. Prepare the machine: Turn the key to the OFF position. A. Park the machine on a level surface. E. Remove the key. B. Lower the attachments. F. C. Set the parking brake. Disconnecting the Hoses Disconnect the battery. Do not disconnect these hoses from the machine. Disconnect the fittings on the trencher drive motor.
PAGE 3
Disconnecting the Plow Hoses Plow 3
PAGE 4
Installing the Mount 6x 6x 12x (3/4 x 2-1/2 inches) (3/4 inch) Assembling and Installing the Valve 2x 2x (3/8 x 3 inches) (3/8 inch) 3x 4 2x
PAGE 5
Installing the Direct Drive Trencher Installing the Trencher on the Mount 6x 6x (3/4 x 2-1/2 inches) (3/4 inch) 5 11x
PAGE 6
Connecting the Hydraulic Lines for the Trencher Install the hoses that were removed from the trencher but not the machine to the ports shown. Install the tee fitting as shown and connect the 76 cm hose (30 inches) to the existing fitting.
PAGE 7
2x 2x 43 cm (17-inches) 2x 2x 56 cm (22 inches) g0374 96 7
PAGE 8
Installing the Plow Installing the Plow on the Mount 5x 5x (3/4 x 2-1/2 inches) (3/4 inch) 8 10x
PAGE 9
Installing the Cylinder Stop 2x 2x (3/8 x 2-3/4 inches) (3/8 inch) Connecting the Hydraulic Lines for the Plow 1x 1x 1x 2x 1x 1x 51 cm (20 inches) 65 cm (25-1/2 inches) 89 cm (35 inches) 140 cm (55 inches) 163 cm (64 inches) 9
PAGE 10
PAGE 11
Use the hose guard and cable ties as needed. 3x 1x Installing the Tires Incrementally torque the wheel nuts for each wheel in the sequence shown below.
PAGE 12
Torquing the Hardware Bolt (3/4 x 2-1/2 inches) Bolt (3/8 x 3 inches) Bolt (3/8 x 2 3/4 inches) 17x x2 x2 12