Form No. 3389-747 Rev A Pro Sneak 365 Vibratory Plow Model No. 25403—Serial No. 314000001 and Up Model No. 25403A—Serial No. 314000001 and Up Model No. 25403C—Serial No. 314000001 and Up Register at www.Toro.com.
WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. Important: This engine is not equipped with a spark arrester muffler.
Contents Safety Safety ........................................................................... 3 Safe Operating Practices........................................... 3 Safety and Instructional Decals ................................. 6 Product Overview .........................................................12 Controls ...............................................................12 Specifications ........................................................14 Attachments/Accessories......................
• • Never leave a running machine unattended. Always stop – Never refuel or drain the machine indoors. – Know the hand signals used on your job. Follow the instructions of the flagmen, signals, etc. Check that the operator's presence controls, safety switches, and shields are attached and functioning properly. Do not operate unless they are functioning properly.
• Do not operate on wet grass. Reduced traction could connecting or disconnecting it from the battery. Wear protective clothing and use insulated tools. cause sliding. • Do not park the machine on a hillside or slope without • Keep all parts in good working condition and all hardware lowering the attachment to the ground, setting the parking brake, and chocking the wheels. tightened. Replace all worn or damaged decals. • Keep nuts and bolts tight.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. Figure 3 1. 2. 3. 4. Decal Decal Decal Decal 117-2718 130-4343 127-1824 130-4340 5. 6. 7. 8. Decal Decal Decal Decal 130-7360 130-4341 130-7361 125-6680 9. 10. 11. 12.
3 1 4 5 6 7 8 9 1 2 10 11 12 13 14 2 g0272 73 Figure 4 1. Decal 125-6684 6. Decal 117-3276 11. Decal 125-6135 (under the seat) 2. Decal 125-6694 7. Decal 125-4963 12. Decal 106-9290 (inside of machine) 3. Decal 125-8491 (behind the rubber guard) 8. Decal 130-4291 13. Decal 125-6694 4. Decal 125-6688 5. Decal 120-0627 (both sides of machine) 9. Decal 125-8483 10. Decal 125-8487 (behind the step) 14. Decal 125-6672 106-9290 1. Inputs 5. In seat 2. Not active 6.
117-3276 1. Engine coolant under pressure 3. Warning—do not touch the hot surface. 2. Explosion hazard—read the Operator's Manual. 4. Warning—read the Operator's Manual. 125–6135 120-0627 1. Cutting/dismemberment hazard, fan—stay away from moving parts, keep all guards and shields in place. 125-6671 1. Explosion hazard; electric shock hazard—call local utilities before digging. 125–4963 1. Warning—keep hands away from hot surfaces 125–6672 1. Crushing hazard—stay away from articulated joints.
125–6688 1. Explosion hazard—Read the Operator’s Manual; Do not use starting fluid. 125–6674 1. Disengage the parking brake. 2. Engage the parking brake. 125–6694 1. Tie down location 125–6680 1. Read the Operator’s Manual. 2. Turn left 4. Fast 3. Slow 6. Traction control 5. Turn right 125–8483 1. Hydraulic fluid; read the Operator’s Manual. 125–6684 1. Cutting/dismemberment hazard, plow—keep bystanders away from the plow; stay away from moving parts; keep all guards and safeties in place.
125–8487 1. Crushing hazard, tire—read the Operator’s Manual; the extension step must be attached when the tires are in wide or doubled configuration. 127-1822 1. The engine cannot start with the plow active. 4. No vibration 2. High vibration 5. The engine can start with the plow inactive. 3. Low vibration 125–8491 1. Crushing hazard, warning—keep away from articulated joints; replace missing safety shields. 130-7361 1. Raise the plow 3. Lower the trencher 2. Lower the plower 4.
130-4291 1. Regeneration inhibit—read the Operator's Manual. 130-4343 5. Warning—keep bystanders away. 2. Warning—do not operate the machine unless you have received instruction. 6. Warning—keep away from moving parts; keep all guards and shields in place. 3. Warning—wear a seatbelt. 7. Warning—do not operate the trencher while using the plow; do not operate the plow while using the trencher. 4. Warning—wear ear 8. Explosion hazard; shock protection.
Controls Product Overview 3 4 Become familiar with all of the controls before you start the engine and operate the machine. 5 6 Throttle 2 The throttle controls the engine speed. Push the knob to increase the engine speed. Pull the knob to decrease the engine speed. 1 Parking Brake Lever To set the parking brake, pull the lever up and push it forward. To release the parking brake, pull the lever back and down. g025662 Attachment Control Lever Figure 5 Right-side view 1. Vibratory plow 3.
Creep-Control Lever The creep control lever controls the direction and speed of the machine while the attachments are in use. To go forward, push the lever forward. To reverse, pull the lever backward. The further you push or pull the lever, the faster the machine will travel. The creep-control lever will not return to the Neutral position on its own. Hour Meter The hour meter displays the number of hours of operation that have been logged on the machine.
Regeneration-Request Light Regeneration-Acknowledge Switch This light illuminates along with the high-temperature-exhaust indicator when a regeneration is in process. If this light is illuminated on its own, a stationary regeneration is possible. When a regeneration is requested but the regeneration inhibit switch is active, this light will blink. If this light is illuminated along with the check engine light, your DPF needs servicing; contact your Authorized Service Dealer for more information.
Filling the Fuel Tank Operation DANGER Note: Determine the left and right sides of the machine from the normal operating position. Refer to Product Overview (page 12). In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Important: Before operating, check the fuel and oil level, and remove debris from the machine. Also, ensure that the area is clear of people and debris.
Note: If the outdoor temperature is below freezing, store the machine in a garage to keep it warmer and aid in starting. 1. Park the machine on a level surface, lower any attachments, stop the engine, and remove the key. 2. Lift the operator seat to access the fuel tank. 3. Remove the fuel tank cap (Figure 9). Stopping the Engine 1. Move the throttle lever to the Slow position. 2. Lower any attachments to the ground. 3. Set all controls to the Neutral position. 4. Set the parking brake. 5.
Note: Do not start the plow vibration until the blade tip has entered the ground. 6. Move the vibratory-plow lever to start the plow vibration. 7. Slowly lower the plow blade into the ground as the machine moves forward. 8. Use the creep control lever to control the direction and speed of the machine during plowing. The machine will move in the same direction that you move the lever. Note: The more you push the lever from the Neutral position, the faster the machine will travel.
Rotating the Wheels The wheels can be installed to provide a narrow or a wide overall width of machine. Install the wheels with the deep concave toward the machine for operation in tight areas or the shallow concave toward the machine for wider stability. Important: Only operate on level ground with the narrow wheel configuration. Pressure Ply Rating Tire Size kPa psi 23 x 10.5 x 12 4 138 20 26 x 12 x 12 8 207 30 g023499 Figure 14 1.
Transporting the Machine Loading the Machine Important: Ensure that the trailer and ramp can support both your weight plus the weight of the machine with any attachments. 1. Start the engine. 2. Move the attachments to transport position. 3. Secure the trailer hitch to your vehicle and put a block at the front and rear of the trailer wheels. 1 4. Move the machine slowly onto the trailer. g018922 Figure 16 5. Lower the attachments onto the trailer and set the parking brake. 1. Rear tie-down loop 6.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Refer to Product Overview (page 12). Important: Refer to your engine Operator's Manual for additional maintenance procedures. Note: Download a free copy of the Electrical Schematic or Hydraulic Schematic for your machine by visiting www.Toro.com and searching for your machine from the Manuals link on the home page.
Maintenance Service Interval Maintenance Procedure Every 1,000 hours • • • • • Change the transmission oil. Change the engine coolant (See an Authorized Service Dealer). Check the alternator drive belt tension. Replace the hydraulic filter. Change the hydraulic fluid. Every 1,500 hours • Replace all moving hydraulic hoses. Every 2,000 hours • Replace the fuel lines and connections. Every 3,000 hours • Clean or replace the diesel particulate filter.
Engine Maintenance Servicing the Air Cleaner Service Interval: Before each use or daily—Check the air filter service indicator light (more frequently if conditions are dusty or sandy). Every 250 hours—Remove the air cleaner cover, clean out any debris, and check the air filter service indicator light (more frequently if conditions are dusty or sandy). Every 500 hours—Replace the air filter (more frequently if conditions are dusty or sandy).
Replacing the Filters SAE 20W -50 If the air filter light illuminates, perform the following steps. SAE 15W -40 1. Gently slide the primary filter out of the air cleaner body (Figure 21). SAE 10W -30 Note: Avoid knocking the filter into the side of the body. SAE 5W -30 SAE 0W -30 2. Inspect the new filter(s) for damage by looking into the filter while shining a bright light on the outside of the filter.
Changing the Oil Filter Note: When using different oil, drain all old oil from the crankcase before adding new oil. 1. Drain the oil from the engine; refer to Changing the Engine Oil (page 24). 2. Place a shallow pan or rag under the filter to catch the oil. 3. Remove the old filter (Figure 25) and wipe the surface of the gasket seal on the filter head. 5. Install the oil fill cap and dipstick. 6. Close the engine cover and secure it with the latches. Changing the Engine Oil 1.
Fuel System Maintenance removed and replaced with a clean DPF. If the DPF is not cleaned at the 50 g/L level, the engine will continue to run at the de-rated 85% power level until the ash accumulation reaches 60 g/L. When the ash level reaches 60 g/L, the engine will de-rate to 50% power. At this time, the DPF is fully plugged and needs to be removed and replaced with a clean DPF; contact your Authorized Service Dealer for more information.
Replacing the Fuel Filter Canister Electrical System Maintenance Service Interval: Every 500 hours—Replace the fuel filter/water separator. Servicing the Battery 1. Clean the filter head and the outside of the fuel filter. Service Interval: Every 100 hours—Check the battery electrolyte level (replacement battery only). 2. Turn the filter counterclockwise and remove the filter from the filter head. 3. Lubricate the gasket on the new filter canister with clean oil.
Drive System Maintenance Servicing the Tires Checking the Tires and Lug Nuts Service Interval: Before each use or daily—Check the tire pressure. Before each use or daily—Check the lug nuts. G025670 Figure 26 1. Positive battery post 3. Red (+) charger lead 2. Negative battery post 4. Black (-) charger lead • Do not exceed the rated tire pressure. To ensure long tire life and safe handling, check tire pressure daily, refer to Checking the Tire Pressure (page 27).
Changing the Transmission Oil Servicing the Transmission and Axles Service Interval: Every 1,000 hours/Yearly (whichever comes first) Transmission oil specification: SAE 80W140 API classification level GL5 1. Park the machine on a level surface, lower any attachments, and stop the engine. Transmission oil capacity: approximately 0.47 L (0.5 qt) 2. Clean the area around the fill plug with a cleaning solvent (Figure 29).
Cooling System Maintenance Note: The oil level should be even with the bottom of the fill plug hole. 4. Add oil to raise the oil level up to the bottom of the fill plug hole. Servicing the Cooling System 5. Install the fill plug. 6. Repeat for the other differential. Service Interval: Before each use or daily—Check and refill the engine coolant. Changing the Axle Oil Every 100 hours—Check the cooling system hoses. 1. Place a drain pan under the pinion housing of the axle.
Belt Maintenance Checking the Engine Coolant Level Check level of coolant at the beginning of each day. Capacity of the system is 8.5 L (9 qt). Checking the Alternator Drive Belt Tension 1. Carefully remove the radiator cap. CAUTION Service Interval: Every 1,000 hours If the engine has been running, the pressurized, hot coolant can escape and cause burns. 1. Push the drive belt with your thumb in the area shown to check the tension (Figure 33).
Controls System Maintenance 4. Run the engine for 5 minutes and check the tension; the tension should be between 7 to 10 mm (1/4 to 3/8 inch) under load of 98 N-m (22 ft-lb). The factory adjusts the controls before shipping the machine However, after many hours of use, you may need to adjust the controls. Important: To adjust the controls properly, complete each procedure in the order listed. Checking the Parking Brake Move the parking brake lever to the On position.
Hydraulic System Maintenance Servicing the Hydraulic System Hydraulic fluid reservoir capacity: 25.8 L (6.8 US gallons) Use only one of the following fluids in the hydraulic system: Toro Premium All Season Hydraulic Fluid (Available in 5-gallon pails or 55-gallon drums. See Parts Catalog or an Authorized Service Dealer for part numbers.
CAUTION During regeneration, the diesel particulate filter becomes extremely hot and can cause serious burns. Keep your body and hands away from the engine during regeneration. 1 5. Remove the cap from the filler neck and check the fluid level on the dipstick (Figure 37). The fluid level should be between the marks on the dipstick. g018923 Figure 36 1. Hydraulic-oil filter 5. Apply a thin coat hydraulic fluid to the rubber gasket on the replacement filter. 6.
Figure 40 1. Hose clamp Figure 38 1. Upper left panel 7. Disconnect the electrical lead to the oil temperature sending unit at the bottom of the reservoir. 2. Hydraulic tank 8. Loosen the hydraulic tank straps and remove the hydraulic tank from the machine (Figure 41). 3. Place a large drain pan (capable of holding 57 liters (15 US gallons) on the ground under the hydraulic tank. 4. Remove the hydraulic tank cap and use a pump to empty the hydraulic tank. 5.
Checking the Hydraulic Lines Service Interval: Every 100 hours—Check the hydraulic lines for leaks, loose fittings, kinked lines, loose mounting supports, wear, weather, and chemical deterioration. (Make necessary repairs before operating.) Every 1,500 hours/Every 2 years (whichever comes first)—Replace all moving hydraulic hoses. WARNING Hydraulic fluid escaping under pressure can penetrate skin and cause injury.
ROPS Maintenance 2. Check that the bolts and nuts that attach the seat-belt retractor and buckle to the seat are torqued to 104 to 115 N-m (77 to 85 ft-lb); refer to Figure 43. Checking and Servicing the ROPS Note: Replace any parts that are worn or damaged. 3. Inspect the ROPS for cracks, rust, or holes in the ROPS and component parts. Checking and Caring for the Seat Belt Note: Age, weather, and accidents cause damage to the ROPS and ROPS parts.
Cleaning Storage 1. Lower any attachments, stop the engine, and remove the key. Removing Debris from the Machine 2. Remove dirt and grime from the entire machine. Important: You can wash the machine with mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water, especially near the control panel, engine, hydraulic pumps, and motors.
Troubleshooting Problem The starter does not crank. Possible Cause 1. The controls are not in the neutral position. 1. Move all of the controls to the Neutral position. 2. The electrical connections are corroded or loose. 3. A fuse is blown or loose. 4. The battery is discharged. 5. The relay or switch is damaged. 2. Check the electrical connections for good contact. 3. Correct or replace the fuse. 4. Charge the battery or replace it. 5. Contact your Authorized Service Dealer. 6.
Problem The engine starts, but does not keep running. Possible Cause 1. The fuel tank vent is restricted. 1. Loosen the cap. If the engine runs with the cap loosened, replace the cap. 2. There is dirt or water is in the fuel system. 3. The fuel filter is clogged. 4. There is air in the fuel system. 2. Drain and flush the fuel system; add fresh fuel. 3. Replace the fuel filter. 4. Bleed the nozzles and check for air leaks at fuel hose connections and fittings between the fuel tank and engine. 5.
Problem The engine overheats. Possible Cause 1. More coolant is needed. 1. Check and add coolant. 2. There is restricted air flow to the radiator. 3. The crankcase oil level is incorrect. 4. The engine load is too excessive. 2. Inspect and clean the side panel screens with every use. 3. Fill or drain the oil to the full mark. 4. Reduce the load; use lower ground speed. 5. Drain and flush the fuel system; add fresh fuel. 6. Contact your Authorized Service Dealer. 7.
Problem The engine loses power. Possible Cause 1. The engine load is excessive. 1. Reduce the load; use lower ground speed. 2. The crankcase oil level is incorrect. 3. The air cleaner filters are dirty. 4. There is dirt, water, stale fuel, or incorrect fuel is in the fuel system. 5. The engine is overheating. 2. Fill or drain to the full mark. 3. Service the air filters. 4. Drain and flush the fuel system; add fresh fuel. 5. Refer to troubleshooting item The engine is overheating. 6.
Notes: 42
Notes: 43
Toro Compact Utility Equipment Warranty Compact Utility Equipment (CUE) Products A One-Year Limited Warranty Conditions and Products Covered Items and Conditions Not Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Compact Utility Equipment (“Product”) to be free from defects in materials or workmanship.
