Installation Instructions

ManualsBrandsToro ManualsTrenchersToro 25415

FormNo.3394-714RevA

BeaconLightKit

RT600orRT1200Trencher

ModelNo.25415

ModelNo.25415E

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachine

fromthenormaloperatingposition.

Safety

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocatednear

anyareaofpotentialdanger.Replaceany

decalthatisdamagedorlost.

120–0771

1.BeaconLight

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparingthemachine.

Decal1

Locatingmountingholesanddecal

placement.

BeaconLight1

BeaconLightMount(RT600only)

Bolt3/8x6inches(RT600only)

Washerhardened(RT600only)

Flangenut(RT600only)

Mountingthebeaconlight.

WiringHarness1

Connectingthewiringharnesstothe

machine.

Switch

SwitchBoot

ConnectingOn/Offswitchandrouting

thewiringharnesstobeaconlight.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3394-714*A

Summary of content (8 pages)

PAGE 1
Form No. 3394-714 Rev A Beacon Light Kit RT600 or RT1200 Trencher Model No. 25415 Model No. 25415E Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Safety and Instructional Decals Safety Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
PAGE 2
1 Preparing the Machine No Parts Required Procedure 1. Move the machine to a level surface. 2. Set the parking brake, shut off the engine, and remove the key from the key switch. 3. Remove the right side panel; refer to the Operator’s Manual. 4. Disconnect the battery; refer to the Operator’s Manual. 2 Locating Mounting Holes and Decal Placement Figure 1 RT600 Parts needed for this procedure: 1 1. 6 mm (0.25 inch) 4. 35 mm (1.375 inch) 2. 66 mm (2.5 inch) 5. 6 mm (0.25 inch) 3. 13 mm (0.
PAGE 3
Figure 2 RT1200 1. 9 mm (0.35 inch) 4. 16 mm (0.625 inch) 2. 44 mm (1.75 inch) 5. 4 mm (0.15 inch) Figure 3 RT1200 1. 318 mm (12.5 inch) 3. 13 mm (0.5 inch) 3. 22 mm (0.875 inch diameter) 2. 127 mm (5 inch) 1. Locate and mark the beacon hole location (Figure 3). 3 2. Drill the indicated hole size at the marked location. Note: Stop drilling immediately after completely penetrating the surface.
PAGE 4
3. Install the mounting hardware back onto the threaded shaft and tighten until secure. Do not over-tighten the retaining hardware. Figure 5 RT1200 1. Beacon light threaded shaft 4 Figure 4 RT600 1. Beacon light 4. Washer hardened 2. Beacon light mounting bracket 3. Flange nut (3/8 inch) 5. Bolt (3/8 x 6 inches) 2. Beacon light mounting hole Connecting the Wiring Harness to the Machine Parts needed for this procedure: 1 Mounting the beacon light to the RT1200 Wiring Harness Procedure 1.
PAGE 5
Figure 6 RT600 1. Insulator Lug 4. Ring-terminal 2. Nut 3. Lock-washer 5. Positive terminal 6. Batery-disconnect switch Figure 7 RT1200 1. Insulator Lug 4. Ring-terminal 2. Nut 3. Lock-washer 5. Positive terminal 6. Batery-disconnect switch 3. Remove the bolt attached to the engine ground. (Figure 8 or Figure 9). 4. Using the bolt you removed, attach the other ring terminal to the engine ground (Figure 8 or Figure 9).
PAGE 6
5 Connecting On/Off Switch and Routing the Wiring Harness to Beacon Light Parts needed for this procedure: 1 Switch 1 Switch Boot Procedure 1. If equipped, remove the panel beneath the dashboard (Figure 10). Figure 8 RT600 1. Bolt 3. Engine ground 2. Ring terminal Figure 10 1. Bolt 2. Kicker panel 2. Route the wiring harness to the operator area and underneath the dashboard (Figure 12 or Figure 13). 3.
PAGE 7
Figure 11 RT1200 Shown 1. Switch Boot 2. Beacon Light Switch Figure 12 RT600 6. Route the remainder of the wiring harness underneath the operator area and connect it to the beacon light (Figure 12 or Figure 13). If necessary, remove the foot plate; refer to the Operator’s Manual. 1. Recommended wiring harness route for the RT600. 7. Use the provided magnetic cable tie mounts and additional cable ties where require to properly secure the wiring harness. Figure 13 RT1200 1.
PAGE 8
Operation Using the Beacon Light 1. Toggle the switch from the Off position to turn the beacon light on. 2. Return the switch to the Off position to turn the beacon light off. Note: Rotate the beacon light switch 180 degrees to achieve the desire On or Off position.