Installation Instructions

ManualsBrandsToro ManualsTrenchersToro 25428E

Table Of Contents

FormNo.3394-793RevA

Back-UpAlarmKit

RT600Trencher

ModelNo.25428

ModelNo.25428E

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Wiringharness1

Screw(#10x1inch)

Washer1

Relay1

Locknut(#10)

Installthewiringharness.

Mountplate1

Linkageplate1

ProximitySwitch

Bolt(3/8x1-1/4inches)

Flangenut(3/8inch)

Sensorbracket

Installtheproximityswitch.

Back-upalarm1

Nut(M6)

Locknut(M8)

Alarmbracket1

Bolt(M6)

Bolt(M8)

Installthealarm.

Clamp

Cabletie

Routethewiringharness.

Nopartsrequired

–

Checkthealarm.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3394-793*A

Summary of content (8 pages)

PAGE 1
Form No. 3394-793 Rev A Back-Up Alarm Kit RT600 Trencher Model No. 25428 Model No. 25428E Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Note: Determine the left and right sides of the machine from the normal operating position. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1 Preparing the Machine No Parts Required Procedure 1. Move the machine to a level surface. Figure 1 2. Set the parking brake and lower the attachments to the ground. 1. Kick panel 3. Shut off the machine and remove the key. 2. Install the relay, wiring harness, washer, screw (#10 x 1 inch), and locknut (#10) to the hole in the console in front of the traction control pedal (Figure 2).
PAGE 3
Attaching the Wiring Harness to the Engine 4. Install the ring terminal of the red wire and the insulator lug (Figure 4). 5. Remove the nut attached to the engine-ground post and use it to attach the ring terminal of the black wire to the engine-ground post (Figure 5). 1. Remove the right side panel and the nose panel. Refer to your Operator’s Manual. 2. Route the wiring harness through the hole shown in Figure 3. Figure 3 1. Relay Figure 5 3. Route through this hole. 1. Nut 2. Wiring harness 2.
PAGE 4
Note: Ensure that the end of the proximity switch extends approximately 3.43 cm (1.35 inches) past the sensory basket (Figure 7). 3 Installing the Proximity Switches Parts needed for this procedure: 1 Mount plate 1 Linkage plate 2 Proximity Switch 2 Bolt (3/8 x 1-1/4 inches) 2 Flange nut (3/8 inch) 1 Sensor bracket Installing the Proximity Switch Under the Machine 1.
PAGE 5
Installing the Proximity Switch in the Seat Mount 4. Apply thread locker to the bolts and install the mount plate to the lever assembly using the bolts and washers (Figure 9). 1. Remove the 2 bolts from the ground-drive-control lever assembly and the nuts and U-bolt inside the seat mount (Figure 8). 5. Use the 2 hex nuts and 2 washers on the proximity switch to install the proximity switch to the plate mount (Figure 9). Note: Retain the hardware. Note: Ensure that the end of proximity switch extends 1.
PAGE 6
Note: Ensure that there is a 0.38 cm (0.15 inch) gap between the linkage plate and the proximity switch (Figure 10). 8. Install the ground-drive-control assembly in the seat mount (Figure 8). 9. Secure the ground-drive-control cable using the U-bolt and 2 bolts removed previously (Figure 8). 10. Torque the bolts to 65 N-m (48 ft-lb) 5 Routing the Wiring Harness Parts needed for this procedure: 4 2 Nut (M6) 1 Locknut (M8) 1 Alarm bracket 2 Bolt (M6) 1 Bolt (M8) 6 Cable tie 1.
PAGE 7
3. Starting from the relay, route the wiring harness along the machine frame (Figure 14). 6. Connect the ring terminal of the gray wire to the positive (top) post of the back-up alarm and connect the ring terminal of the black wire to the negative (bottom) post (Figure 15). 7. Route the remaining loose end between the ROPS bracket and rear bulkhead, through the clamps on the rear bulkhead, and then underneath the seat (Figure 15). 8.
PAGE 8