Installation Instructions

ManualsBrandsToro ManualsTrenchersToro 25439E

FormNo.3377-972RevB

CounterweightKit

RT600TractionUnit

ModelNo.25439

ModelNo.25439E

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Mountingframe

Bolt(1-1/4x3-1/2inch)

Washer(1-1/4inch)

Installthemountingframe.

Counterweight

Rod1

Washer(5/8inch)

Locknut(5/8inch)

Installthecounterweights.

PreparingtheMachine

1.Movethemachinetoalevelsurface.

2.Settheparkingbrakeandlowertheattachmentsto

theground

3.Shutoffthemachineandremovethekey.

4.Ifafront-mountedattachmentsuchasthebackhoe

orcablecarrierisinstalledonthemachine,remove

theattachment;refertotheOperator’sManualforthe

attachment.

InstallingtheMountingFrame

Note:Yourliftingequipmentmusthavealiftcapacityof

136kg(300lb).

Note:Removeallcounterweightkithardwareandweights

fromthemountingframepriortoinstallationofthe

counterweightkit.Eachcounterweightweighsapproximately

29.9kg(66lb).

1.Removethe2locknuts(5/8inch),2washers(5/8

inch),androdthatsecurethecounterweightstothe

mountingframe.

Note:Retainthelocknuts,washers,androdfor

installationinstep

2ofInstallingtheCounterweights.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3377-972*B

Summary of content (4 pages)

PAGE 1
Form No. 3377-972 Rev B Counterweight Kit RT600 Traction Unit Model No. 25439 Model No. 25439E Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 2
5. Install the bolts (1-1/4 x 3-1/2 inch) and washers (1-1/4) that fasten the mounting frame to the machine (Figure 2), and hand tighten all of the bolts. 2. Using the lifting equipment, remove the counterweights from the mounting frame. 3. Use lifting equipment to raise or lower the mounting frame until the holes in the mounting frame align with the holes in the machine; refer to Figure 1. 1 2 12 2 1 12 Figure 1 1. Mounting frame g022274 Figure 2 3. Hole (machine chassis) 1. Washer 2.
PAGE 3
Installing the Counterweights 2. Secure the counterweight(s) to the mounting frame with the rod, washers, and locknuts that you removed in step 1 of Preparing the Machine; refer to Figure 4. 1. Use the lifting equipment to lift and install one or more of the counterweights onto the mounting frame; refer to Figure 3. 1 Note: Do not overtighten the nuts. Tighten the nuts only enough to prevent the washers from rattling. 3 2 2 g022275 1 Figure 3 1. Mounting frame 2.
PAGE 4