Form No. 3407-774 Rev A イ ン チ, 60イ イ ン チ, 72イ インチ 油圧クラムバー 48イ RT1200 ト ラ ク シ ョ ン ユ ニ ッ ト 用 モ デ ル 番 号 25446 モ デ ル 番 号 25446E モ デ ル 番 号 25447 モ デ ル 番 号 25447E モ デ ル 番 号 25448 モ デ ル 番 号 25448E 取り付け要領 安全について 警告 カリフォルニア州 第 65 号 決 議 に よ る 警 告 米国カリフォルニア州では、この製品に、ガンや先天性異常などの原因とな る化学物質が含まれているとされております。 安全ラベルと指示ラベル 以下のラベルや指示は危険な個所の見やすい部分に貼付してあります。 破損したりは がれたりした場合は新しいラベルを貼付してください。 decal125-6670 125-6670 1.
取り付け 付属部品 すべての部品がそろっているか、下の表で確認してください。 手順 1 2 3 4 5 数量 内容 用途 必要なパーツはありません。 – マシンの準備を行います。 クラムバーチューブアセンブリ クラムバープレートアセンブリ アダプタフィッティング 油圧ホース ホース取り付けクランプ ボルト1/2 x 2-1/4 インチ チューブクランプ カバープレート ボルト5/16 x 1-1/2 インチ ボルト3/8 x 2-1/2 インチ 六角ナット3/8 インチ 上側アングルコンジット 下側アングルコンジット 背高、前側アングルコンジット 背高、後側アングルコンジット アングルタイ ワッシャ ボルト1 x 2-1/2 インチ 六角ナット1/2 インチ ボルト3/8 x 2-1/2 インチ ボルト 3/8-16 x 1 インチ ボルト3/8 x 2-3/4 インチ 1 1 2 2 2 4 4 2 2 3 3 1 1 1 1 1 2 2 5 3 1 1 クラムバーチューブとプレートアセンブ リを取り付けます。 スイッチ 1 スイッチを取り付けます.
1 マシンの準備を行う 必要なパーツはありません。 手順 1. 平らな場所に駐車する。 2. アタッチメントを下げる。 3. 駐車ブレーキを掛ける。 4. エンジンを止め、キーを抜き取る。 g038689 図1 2 クラムバーチューブとプレートアセ ンブリを取り付ける この作業に必要なパーツ 1 クラムバーチューブアセンブリ 1 クラムバープレートアセンブリ 手順 重要 この作業は二人で行うか、ホイストなどを使 用して行う必要があります。 1. クラムバー取り付けブラケットをブームに固 定しているボルト4本とロックナット4個を外 す図 2。 g031720 図2 2.
クラムバープレートアセンブリをクラムバー チューブアセンブリに、図 2のように取り付 ける。 3. 3 油圧ホースを取り付ける この作業に必要なパーツ 2 アダプタフィッティング 2 油圧ホース 2 ホース取り付けクランプ 4 ボルト1/2 x 2-1/4 インチ g038691 図4 手順 1. 6. アダプタフィッティング2個を機体に取り付 ける 図 3 。 シリンダの上ポートから来ているホースを機 体の右側のポートに取り付ける図 5。 g038692 図5 g038690 図3 2. ボルト 4本とワッシャ、ナットを取り外す図 3。 注 ボルトは廃棄する。 3. ホース取り付けクランプを取り付けるボルト 1/2- x 2 -1/4 インチ4本、ワッシャ4枚と先ほ ど取り外したナットを使用し図 3のように取 り付ける。 4. ボルトを127157N·m3.74.6kg.m = 94~116 ft-lbにト ルク締めする。 5.
4 油圧ホースを固定する この作業に必要なパーツ 4 チューブクランプ 2 カバープレート 2 ボルト5/16 x 1-1/2 インチ 3 ボルト3/8 x 2-1/2 インチ 3 六角ナット 3/8 インチ 1 上側アングルコンジット 1 下側アングルコンジット 1 背高、前側アングルコンジット 1 背高、後側アングルコンジット 1 アングルタイ 2 ワッシャ 2 ボルト 1 x 2-1/2 インチ 5 六角ナット 1/2 インチ 3 ボルト3/8 x 2-1/2 インチ 1 ボルト 3/8-16 x 1 インチ 1 ボルト3/8 x 2-3/4 インチ g038693 図6 ボルトを3137N·m3.74.6kg.m = 23~28 ft-lbにト ルク締めする。 3. 上下のアングルコンジットをフレーム上のブー ム取り付けプレートに取り付けるボルト3/8 x 2-1/2 インチ3本と六角ナット3/8 インチ3個を 使用して図 7のように取り付ける。 注 ブーム上昇状態ではホースに全くたるみが 出ていないのが適正です。 手順 1.
g038694 図7 4. 3本のボルト3/8 x 2-1/2 インチを 5165 N.m5.36.6 kg.m = 3848 ft-lbにトルク締めする。 5. クラムバーブラケットバーからボルトとナッ トを外す 図 8 。 注 ボルトは廃棄する。 g031726 図8 6. 図 8に示すように、アングルタイを背高前側ア ングルコンジットに固定するボルト 1/8- x 3 イ ンチ 1本、ナット 3/8 インチ 1個を使用する。 7. ボルト3/8 x 1 インチを5165N·m 5.36.6 kg.m = 3848ft-lbにトルク締めする。 8. 背高前側アングルコンジットをクラムバーブ ラケットに固定するワッシャ2枚、ボルト1 x 2 -1/2 インチ2本と、先ほど取り外したボルト 2本を使用する図 8。 9. 2本のボルト 1 x 2-1/2 インチ を 732 894N·m 7591kg.m = 540660ft-lbにトルク締めする。 10.
12. 図 8に示すように、アングルタイを高低アン グルコンジットアセンブリに取り付けるボル ト 3/8 x 2-3/4 インチ 1本、ナット 3/8 インチ 1 個を使用する。 13. ボルト3/8 x 2-3/4 インチを6076N·m 9.311.5kg.m = 4456ft-lbにトルク締めする。 3. プラグを打ち抜き、出来た穴にスイッチを取 り付ける 図 10 。 5 スイッチを取り付ける この作業に必要なパーツ g031727 スイッチ 1 図 10 手順 1. 4. plow tilt というラベルのついたワイヤハーネス をスイッチに接続する。 後カバープレートを機体の後バルクヘッドに 固定している六角フランジボルト12 x 30mm6本 を外して、カバープレートを取り外す図 9。 5. g025321 図9 1. バルクヘッド 2. 後カバープレート 2. 3.