Installation Instructions

ManualsBrandsToro ManualsTrenchersToro 25454

FormNo.3377-984RevA

SlidingAttachmentKit

RT1200Trencher

ModelNo.25454—SerialNo.314000001andUp

ModelNo.25454E—SerialNo.314000001andUp

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Slidemount

Pivotpin1

Boomcylinderpin1

Threadedrod2

HexNut4

FlatWasher(5/8inch)

Retainingring2

Screw(3/8inch)

Washer(3/8inch)

Nut(3/8inch)

Slideplate

Wearstrip2

Upperslideplate1

Idlerwheel2

Bearing2

Chainassembly

Rolleraxle2

Squareholewasher

Washer(21/2inch)

Washer(5/8inch)

Hexbolt(5/8x13/4inch)

Hexbolt(5/8x23/4inch)

Hydrauliccylinderboom1

Assemblethekit

Nopartsrequired

–

Preparethemachine.

SideShift

Bolt6

Washer6

Nut6

Hydraulicline2

Installthemountingframe.

Note:Additionalhydrauliccomponentsarerequiredforthe

operationofthiskit.PleaseseeyourAuthorizedToroDealer

foradditionalinformation.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3377-984*A

Summary of content (8 pages)

PAGE 1
Form No. 3377-984 Rev A Sliding Attachment Kit RT1200 Trencher Model No. 25454—Serial No. 314000001 and Up Model No. 25454E—Serial No. 314000001 and Up Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 2
WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 3
Assembling the Sliding Attachment Kit 1 1. Stack the boom idler wheel assembly (Figure 1). 1 2 3 1 g025743 Figure 1 1. Square-hole washer 3. Bearing 2 3 2. Idler wheel 2. Slide the boom-idler wheel into the slid mount assembly, and insert the slide plate and wear strip (Figure 2). 4 5 2 6 7 8 4 g025744 Figure 2 3 1. Boom idler wheel 5. Wear strip 2. Wear strip 6. Washer 3. Slide plate 7. Roller axle 4. Hex bolt (5/8 x 1 3/4 inch) 8.
PAGE 4
3. Slide the-side-boom idler wheel into the mount assembly (Figure 3). 1 1 2 3 4 g025745 2 Figure 3 1 1. Side-boom-idler wheel 4. Install the roller axle to secure the roller into place (Figure 4). Note: Slide the boom so that you can install the top bolt. g025746 Figure 4 1. Hex bolt (5/8 x 1 3/4 inch) 3. Right-boom-idler wheel 2. Washer (2 1/2 inch) 4. Roller axle 5. Install the threaded rods to the attachment (Figure 5). 1 2 3 1 Figure 5 1. Hex nut 2. Threaded rod 4 3.
PAGE 5
6. Install the chains to the frame of the attachment (Figure 6). 8. Attach the chain assembly to the threaded rods (Figure 8). 2 1 2 3 4 1 3 3 4 4 3 2 1 g025750 Figure 8 1. Chain assembly 3. Chain retaining pin 2. Chain pin 4. Threaded rod 9. Install the piston mounting fitting end of the hydraulic cylinder to the attachment frame (Figure 9). 2 5 5 2 1 g025748 2 Figure 6 3 1. Flat washer (5/8 inch) 4. Attachment frame 2. Chain pin 5. Chain-retaining pin 4 3.
PAGE 6
10. Install the cylinder mounting fitting end of the hydraulic cylinder to the attachment frame (Figure 10). 1 2 3 1 2 4 5 6 g025752 Figure 10 1. Cylinder-mounting fitting 4. Washer (3/8 inch) 2. Attachment frame 5. Boom cylinder pin 3. Nut (3/8 inch) 6.
PAGE 7
Preparing the Machine 1 2 1. Move the machine to a level surface. 2. Set the parking brake and lower the attachments to the ground 3. Stop the engine and remove the key. 4. If a rear-mounted attachment such as the backhoe is installed on the machine, remove the attachment; refer to the Operator’s Manual for the attachment. 3 Installing the Mounting Frame Note: Your lifting equipment must have a lift capacity of 136 kg (300 lb).
PAGE 8