Form No. 3395-684 Rev A Counterweight Kit and Counterweight and Reel Kit RT1200 Trencher Model No. 25458 Model No. 25458E Model No. 25459 Model No. 25459E Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
Description Reel collar Spindle Hex bolt (5/8 x 1-1/2 inch) Bolt (3/8 x 5-1/2 inch) Washer Nut Cylinder pin Retaining ring Clevise pin Hair pin Plow lift Hydraulic hose Tee fitting Hex bolt (5/16 x 1-3/8 inch) Cover plate Hose mount Rocker switch Use Qty. 2 1 2 2 2 2 2 4 4 4 2 4 2 2 2 2 1 Install the reel (models 25459 and 25459E only). Preparing the Machine 1. Move the machine to a level surface. 2. Set the parking brake and lower the attachments to the ground 3. Stop the engine and remove the key. 4.
Installing the Mounting Frame 5. Install the bolts and washers to fasten the mounting frame to the machine (Figure 2). Note: Your lifting equipment must have a lift capacity of 136 kg (300 lb). Note: Hand-tighten the bolts. Note: Remove all counterweight kit hardware and weights from the mounting frame prior to installation of the counterweight kit. Each counterweight weighs approximately 30 kg (66 lb). 1 2 3 4 1.
Installing the Counterweights 3. Secure the counterweight(s) to the mounting frame with the rod, washers, and locknuts that you removed in step 1 of Preparing the Machine (page 2); refer to Figure 5. 1. If not already installed, install a strut pad to the inside of each side of the mounting frame using the adhesive side of each strut pad. Note: Do not overtighten the nuts. Tighten the nuts only enough to prevent the washers from rattling. Figure 3 1. Strut pad 2.
Installing the Reel 3. Mount the reel carrier arm to the counterweight frame using 4 retaining rings and 2 pins (Figure 8). Models 25459 and 25459E 1. Assemble the spindle (Figure 6). Figure 8 Figure 6 1. Reel collar 3. Hex bolt (5/8 x 1-1/2 inch) 2. Spindle 4. Washer 1. Retaining ring 2. Pin 4. Mount the lift cylinders to the machine using 4 hair pins and 4 clevis pins (Figure 9). 2.
4 5. Install the hydraulic hoses and tee fittings to the lift cylinders and the machine (Figure 10 and Figure 11). 3 Note: The hydraulic port on the machine is located on the bottom right side of the front of the machine. Note: Connect the hoses by corresponding letters (A, B, C, and D) in Figure 10 and Figure 11. 5 5 1 2 3 4 2 Figure 11 1. Hose A 2. Hose B 3. Hose C g025333 Figure 10 1. Hose A 2. Hose B 3. Hose C 4. Hose D 6 4. Hose D 5.
6. Install a hose clamp to the inside of each side of the mounting frame (Figure 12). Figure 12 1. Hose clamp 3. Hex bolt (5/16 x 1-3/8 inch) 2. Cover plate 7. On the control panel, remove the dash-switch plug, transfer the wiring harness connector to the rocker switch, and install the rocker switch (Figure 13). Note: If the wiring harness is not attached to the hole plug, reach under the control panel to find the wiring harness and connect it to the switch. Figure 13 1. Dash-switch plug 2.