Installation Instructions

ManualsBrandsToro ManualsTrenchersToro 25460E

FormNo.3378-102RevA

AuxiliaryHydraulicsKit

RT1200Trencher

ModelNo.25460

ModelNo.25460E

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

127-1831

1.Plowswing5.Plow-headtilt

2.Rocksawstabilizerheight6.Plowheight

3.Auxiliaryfunction7.Sideshift

4.Crumberheight/Plowattitude

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-102*A

Summary of content (8 pages)

PAGE 1
Form No. 3378-102 Rev A Auxiliary Hydraulics Kit RT1200 Trencher Model No. 25460 Model No. 25460E Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
PAGE 2
Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. No parts required – Remove the rear-cover plate. Rear-attachment hydraulic valve 1 Connect the hydraulic lines to the hydraulic fittings. Valve-mount plate Hex-head screw (12 x 30 mm) 1 2 Install the valve-mount plate. Rear-attachment hydraulic valve 1 Connect the wiring-harness connectors to the coils. No parts required – Understand the hydraulic connections.
PAGE 3
2 Connecting the Hydraulic Lines to the Hydraulic Fittings Parts needed for this procedure: 1 Procedure Figure 3 1. Frame-mount plate Rear-attachment hydraulic valve 1. Remove the 3 hydraulic lines (pressure, return, and load sense) from the clamp (behind the frame-mount plate), and move the lines to the right, toward the proximity of the hydraulic fittings on the rear-attachment hydraulic valve (Figure 5). 3. Hex-head screws (12 x 50 mm) 2. Cover plate 4. Remove the cover plate (Figure 4).
PAGE 4
3 Installing the Valve-mount Plate Parts needed for this procedure: 1 Valve-mount plate 2 Hex-head screw (12 x 30 mm) Figure 6 1. Hydraulic-return fitting (labeled T on the rear-attachment hydraulic valve) 4. Hydraulic-pressure line 2. Hydraulic load-sense fitting (labeled LS on the rear-attachment hydraulic valve) 5. Hydraulic load-sense line 3. Hydraulic-pressure fitting (labeled P on the rear-attachment hydraulic valve) 6. Hydraulic-return line Procedure 1.
PAGE 5
4 Connecting the Wiring-harness Connectors to the Coils Parts needed for this procedure: 1 Rear-attachment hydraulic valve Procedure See the following figure for connecting the wiring-harness connectors into the front and back of the coils on the rear-attachment hydraulic valve. Figure 8 Note: To make sure that there is a solid connection, ensure that the wiring-harness connectors are securely inserted into their respective coils on the rear-attachment hydraulic valve. 1. Plow swing right 6.
PAGE 6
5 6 Understanding the Hydraulic Connections Installing the Rear-cover Plate No Parts Required No Parts Required Procedure Procedure 1. Align the 3 holes on the rear-cover plate with the corresponding holes on the frame-mount plate (Figure 10).
PAGE 7
Notes: 7
PAGE 8