Installation Instructions

ManualsBrandsToro ManualsTrenchersToro 25464

FormNo.3378-114RevA

WorkLightKit

RT1200Trencher

ModelNo.25464

ModelNo.25464E

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Wiringharness1Routethewiringharness.

Worklight4Installtheworklights.

RoutingtheWiringHarness

1.Connectthe4-pinconnectorofthewiringharnessto

the4-socketconnectorofthemachineharnessunder

thedashboard(Figure1).

Figure1

1.4-pinconnector2.4-socketconnector

2.Movetheharnessdownandtotheleftfromunderthe

dashboard.

3.Routetheharnessalongthekick-platepanelandthe

steering-consolepanel,andsecuretheharnesswiththe

magnetictie-mountwraps(Figure2).

Figure2

1.Steering-consolepanel

3.Wiringharness

2.Magnetictie-mountwraps4.Kick-platepanel

4.RoutetheharnessalongtheinsideoftheROPS-post

tube,andsecuretheharnesswiththemagnetic

tie-mountwraps(Figure3).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-114*A

Summary of content (4 pages)

PAGE 1
Form No. 3378-114 Rev A Work Light Kit RT1200 Trencher Model No. 25464 Model No. 25464E Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. Wiring harness 1 Route the wiring harness. Work light 4 Install the work lights. Routing the Wiring Harness 1.
PAGE 2
Figure 3 Figure 5 3. Wiring harness 1. ROPS-post tube 1. Front ROPS light-cover plate 2. Magnetic tie-mount wraps 5. Route the two 2-socket connectors on the wiring harness through the front ROPS-plate holes (Figure 4). 7. Route the wiring harness along the inside of the ROPS post-tube, and secure the harness with the magnetic tie-mount wraps (Figure 6). Note: Ensure that the harness is routed on the inside of the front ROPS plate. Figure 4 1. ROPS plate 2. 2-socket connectors Figure 6 3.
PAGE 3
. Remove the 4 hex-head screws and the 2 cover plates from the rear ROPS light-cover plate (Figure 10). Note: Discard the 4 hex-head screws and the 2 cover plates. Figure 7 1. Rear ROPS light-cover plate 2. 2-socket connectors Figure 10 2. Hex-head screw 1. Cover plate Installing the Work Lights 1. Remove the 4 hex-head screws and the 2 cover plates from the front ROPS light-cover plate (Figure 8). 4.
PAGE 4
Operation 2. Insert the new light-bulb assembly at the horizontal position, and turn the knob clockwise 1/4 turn back to the original, vertical position (Figure 14). Operating the Work Lights Important: Do not touch the light bulb during assembly, as this will shorten the life of the light bulb. Press button number 1 on the main display screen to turn the work lights on or off (Figure 12). Figure 14 1. Light-bulb assembly Figure 12 Work Lights Shown in the On Position on the Screen 1.