Installation Instructions

ManualsBrandsToro ManualsTrenchersToro 25468E

FormNo.3378-127RevA

BlockHeaterKit

RT1200Trencher

ModelNo.25468

ModelNo.25468E

InstallationInstructions

Installation

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

PreparingtoInstalltheBlock

Heater

NoPartsRequired

DrainingtheCoolant

WARNING

Coolantistoxic.

•Keepcoolantawayfromchildrenandpets.

•Ifnotreused,disposeofcoolantinaccordance

withlocalgovernmentregulations.

WARNING

Heatedcoolantsprayorsteamcancausepersonal

injury.

•Donotremovetherecoverytankcapwhenthe

engineishot.

•Waituntilthecoolanttemperatureisbelow50°C

(120°F)beforeremovingtherecoverytankcap.

Important:Donotpourcoolantontothegroundorinto

anunapprovedcontainerthatcanleak.

1.Movethemachinetoalevelsurface,shutoffthe

engine,andremovethekeyfromthekeyswitch.

2.Allowtheengineandcoolingsystemtocool.

3.Removetheleftandrightsidepanels;refertoOperator’s

Manualforthemachine.

4.Removetherecovery-tankcapfromthetank(Figure1).

g024982

Figure1

1.Recovery-tankcap2.Fillerneck

5.Placeadrainpanwithaminimumcapacityof23L

(6USgallons)undertheopenendofthedrainhose

(Figure3).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-127*A

Summary of content (8 pages)

PAGE 1
Form No. 3378-127 Rev A Block Heater Kit RT1200 Trencher Model No. 25468 Model No. 25468E Installation Instructions Installation WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. 2. Allow the engine and cooling system to cool. 1 3. Remove the left and right side panels; refer to Operator’s Manual for the machine. Preparing to Install the Block Heater 4.
PAGE 2
Removing the Freeze Plug 1. Locate the forward freeze plug at the right side of the engine. Figure 2 1. Drain hose Figure 4 6. Open the drain valve on the radiator and allow the coolant to drain completely. 1. Freeze plug (right side of engine) Note: Dispose of the used coolant properly according to local codes. 2. Remove the freeze plug. Figure 3 Figure 5 1. Drain valve 3. Thoroughly clean the hole in the engine block with a rag. 7. Close the drain valve (Figure 3).
PAGE 3
2 Installing the Block Heater Kit Parts needed for this procedure: 1 Block heater 2 Flanged-head bolts (8 x 16 mm) 1 Heater-electrical cord 1 Cable tie Procedure 1. Lubricate the O-ring on the block heater with 15W-40 engine oil. Figure 7 1. Connector (electrical cord) 2. Insert the block heater into the hole in the engine block with the element of the heater pointing down (Figure 6). 2. Connector (block heater) 7. Route the cord over the top of the right-frame channel of the machine (Figure 8).
PAGE 4
Note: If the coolant level is low, add coolant to the recovery tank until the fluid level is up to the midpoint of the sight gauge. 3 7. Install the side panels; refer to Operator’s Manual for the machine. Filling the Cooling System with Antifreeze Operation No Parts Required Using the Block Heater Procedure Connecting the Block Heater to Electrical Power The coolant capacity of the engine and the radiator: 18.5 L (19.5 US qt).
PAGE 5
Disconnecting the Block Heater from Electrical Power 1. Disconnect the extension cord from the outlet that is serving as the electrical source for the block heater (Figure 10). 2. Remove the right side panel; refer to the Operator’s Manual for the machine. 3. Disconnect the cord of the block heater cord into the extension cord (Figure 10). 4. Stow the cord of the block heater in the engine compartment, away from moving parts. 5. Install the right side panel; refer to the Operator’s Manual for the machine.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8