Installation Instructions

ManualsBrandsToro ManualsTrenchersToro 25520E

FormNo.3386-813RevA

RearSteeringIndicatorKit

RT600TractionUnit

ModelNo.25520

ModelNo.25520E

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Rear-steeringindicatordecal(125-6697)

Steeringwarningdecal(125-8471)

Applythedecalstothesteering-indicator

plate.

Nopartsrequired

–

Removetherightfenderfromthe

machine.

Position-indicatorcable1

Locknut(M10)

Balljoint1

Plate1

Flangenut(3/8inch)

Clamp(3/8x3/8inch)

Hex-headscrew(3/8x1inch)

Installtheposition-indicatorcable.

Nopartsrequired

–

Installtherightfenderontothemachine.

Locknut(M10)

Position-indicatorpointer1

Installtheposition-indicatorpointer.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3386-813*A

Summary of content (8 pages)

PAGE 1
Form No. 3386-813 Rev A Rear Steering Indicator Kit RT600 Traction Unit Model No. 25520 Model No. 25520E Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 2 3 No parts required – Prepare the machine.
PAGE 2
1 2 Preparing the Machine Applying the Decals to the Steering-indicator Plate No Parts Required Parts needed for this procedure: Procedure 1. Move the machine to a level surface. 2. Set the parking brake and lower the attachments to the ground 1 Rear-steering indicator decal (125-6697) 1 Steering warning decal (125-8471) 3. Shut off the machine and remove the key. Procedure 4. Use a jack with a capacity of 2,494 kg (5,500 lb) to raise the machine at the rear axle.
PAGE 3
Removing the Right Fender from the Machine No Parts Required Procedure 1. Remove the 2 bolts and locknuts from the side of the back ROPS plate (Figure 2). Figure 3 1. Right fender 3. Front ROPS plate 2. Bolt and locknut 4. Remove the right fender from the machine (Figure 3). 4 Installing the Position-indicator Cable Figure 2 1. Bolts and locknuts 3. Back ROPS plate 2. Right fender Parts needed for this procedure: 2. Remove the 2 bolts and locknuts from the bottom of the right fender (Figure 2).
PAGE 4
Figure 6 Figure 4 1. Steering-indicator plate 1. Position-indicator cable 2. Rear-steering mount 3. Position-indicator cable 2. Front ROPS plate 4. Secure the position-indicator cable to the rear axle with the plate, locknut (M10), and the ball joint (Figure 7). 2. Secure the position-indicator cable to the back ROPS plate with the flange nut (3/8 inch), clamp (3/8 x 3/8 inch), and the hex-head screw (3/8 x 1 inch) as shown in Figure 5. Figure 7 1. Position-indicator cable 2. Ball joint Figure 5 1.
PAGE 5
6 Installing the Right Fender onto the Machine Installing the Position-indicator Pointer No Parts Required Parts needed for this procedure: Procedure 1. Align the right fender with the holes where the 5 bolts and the 5 locknuts were removed in 3 Removing the Right Fender from the Machine (page 3). 2 Locknut (M10) 1 Position-indicator pointer Procedure 1. Insert the position-indicator cable through the side of the steering-indicator plate (Figure 8). 2.
PAGE 6
Operation Centering the Rear Wheels Center the rear wheels from left to right by adjusting the ball joint and the locknut at the end of the position-indicator cable until the indicator at the operator’s position shows that the wheels are straight (Figure 10). Figure 10 1. Position-indicator cable 3. Locknut (M10) 2.
PAGE 7
Notes: 7
PAGE 8