BOG NO. ROPE STARTER, LOCKING DIFFERENTIAL, 7702 32" WHIRLWIND S.P.
R T NNV R8s The TOR Owner This Owner Manual has been especially prepared for your information and guidance in the operation and care of your new Toto $2-inch Whirlwind S.P. Properly adjusted, operated and maintained, this Toto Whirlwind will respond quickly and easily to every reasonable demand and give years of reliable service, ‘The Toto Whirlwind is manufactured by an organization of mowing machinery specialists for over 40 years. Bach unit is carefully inspected and tested before leaving the factory.
SPECIFICATIONS ENGINE: Briggs & St ration 28AB rope start FUEL TANK CAPACITY: 8 guards CUTTER BAR CLUTCH: Tight-slack flat belt TRACTION CLUTCH: Rockford disc type on speed reducer output shaft. CUTTER BAR DRIVE: wide flat belt on ©,D. and 0. D, pulleys. REDUCTION: Engine to cutter bax: 1.26:1 CUTTER BAR: arm with hardened blades riveted to ends; 32" long assembled, TRACTION DRIVE: "A" section V-belt on 2.8 P.D,, 3.7 P.D. or 4.9 P.D, engine pulley to 6.8 P.D., 5.3 P.D. or 4.3 P.D. pulley on speed reducer.
OPERATING INSTRUCTIONS FIG. A, HEIGHT OF CUT ADJUSTMENT To change height of cut, insert spanner wrench A’ in position on cutter shaft pulley. Then place wrench “B"on large nut and turn in direction as shown, After nut is loose, threaded shaft “D' can be turned down for low cut or up for high cut as desired. Holes "C in shaft are spaced in 1/2" increments. No adjust~ meets are necessary under housing. FIG. B.
TRANSMISSION ASSEMBLY Drawing No, 7702~5 Ref. No. Ref.. No. No.| Part No, Description Used No.| Part No. Description Used | Housing 1 39 1362-150 | Lock Plug 1 2 $211-6 |Screw, 8/8" N.F. x 13 4 407 1321302 | Set Resew 1 3| 281-2 Plug 2 41 | 352186 | Clutch Body i 4 3256-24 | Washer, 3/8" Cut S.A.E. 4 43 |352-151 Plate Says. , incl Refs. 448 45 2 6 $998-6 | Lockout, 3/8" N.F. 4 44 |3562-155 | Facing 2 6 W-280 | Bearing Cap 1 45 |2118-22 Rivet 12 7 | 321-8 Screw, ¥ N.C.
MAIN FRAME ASSEMBLY PARTS LIST Ref. No. Ref. No. No. {Part No. Description Used No. {Part No.
CONTROL LINKAGE ASSEMBLY PARTS LIST Ref. ~ No. Ref. No. No. [Part No, Description Versed No. | Part No, Description Used 1 14-1120 Main Frame 1 31 {52120-48 | Retaining Ring B 2 [3-2881 Cutter Spindle Housing i 32 |4-9170 Belt Idler, Reverse 1 3 14-1350 Cantilever Frame 1 33 |251-132 Bearing 4 4 13220-8 Nut, 5/8" N.F.
SULKY ASSEMBLY PARTS LIST Ref. No. Ref. No. No. | Part No. Description Used| No. | Part No. Description Used| T |8-2140 | Sulky Frame 1 44 [322-2 | Screw, 3/4" 8 2 |256-85 | Bushing 2 45 [3254-2 | Lock washer, Shockproof.
DIFFERENTIAL CLUTCH ASSEMBLY PARTS LIST Ref. No. Ref, No. No. | Part No. Description Used No.} Part No. Description Used! 1 }231-2 Tire 2 36 | 3-3472 Pedal |232-2 Tube 2 a7 8-3471 Pedal |241-13 Wheel Duse, Inner 2 38 8331-4 x 3/4" Caseworker 1 4 1241-12 ‘Wheel Disc, Outer 2 39 | 3217-§ Hex Nut 1 5 |323-4 x 3/4" Cap screw 12 40 | 3-14438 Bracket Return Spring 1 8 |3253-5 3/8'" Heavy Lock washer 12 41 | 3-1450 Bracket R, H. 1 732177 Hex, Nut 12 42 8-1428 bracken: L.H 1 8 |32140-15] x 5/8 Hex.
REAR AXLE ASSEMBLY PARTS LIST Ref. No. Ref| No. No, [Part No. Description Used No. {Pat No. Description Used 1 [281-2 Tire 2 21 [WW-5581 | Side Gear 1 2 232-2 Tube 2 22 [WW-5598A] Bushing 1 3 |241-12 ‘Wheel Disc, Outer 2 23 |3245-1 Set Screw 2 4 124113 ' | Wheel Disc, Inner 2 24 [WW6I0T Pin, Differential Pinion 2 5 [WW5158 Key 2 25 1251-82 Bearing 2 B8 13-2242 ‘Wheel Hub, |237-39 Quad Ring 1 7 |WW-5577 | Bevel Gear, Long-Hub 1 27 |3-1484 ‘Wheel Hub R.H.
TOR INSTALLATION INSTRUCTIONS and PARTS LIST for Steel Wheel Kit No. 26210 T 12— rp— PARTS LIST Ref, No.| Part No, Description 1 14-1750 Front Wheel 2 %2 | 4-1780 | Wheel Housing Cap 2 3 {251-135 | Bearing 2 4 14-1210 | Spring Seat 2 8 14-123¢ | Spring 2 6 14-1230 | Wheel Housing, Leif 1 * 14-1200 | Wheel Housing, Right 1 T M-82 Plug 2 8 3246-2 | Set Screw 4 § |4-1150 | Bushing 2 10 1301-11 | Tiler 2 11 |32146-5 | Stop Nut 8 12 13256-24 |Washer, 8.A.E.
. For Wheel Caster Kit No.26220 & " i PARTS LIST =1 i Ref. Part No. Description Used t E‘/" 1 11-9399 | Wheel Assembly 2 2 | PL~111 | Singer 4 3 | 3-1705 | Caster Fork Assembly | 2 4 |323-25 | Cap Screw 2 5 |3296-11 | Nut, Elastic Stop 2 6 |302-5 Grease Fitting 4 7 |3-1708 | Singer 4 & |251-34 | Bearing 4 9 |3-1708 | Caster Plate 2 10 | 828615 | Nut, Elastic Stop 2 11 | 3210-2 | Resew 8 12 |3253-4 | Lock washer 8 13 | 32113-10] Screw 6 14 | 3-1704 | Caster WheelDiscL. H.
ENGINE No. 221-112 DRAWING “A” soot? sy, 2 29 Tree —Baby asst mm % FOR CARBURETOR OVERHAUL KIT ORDER PART NO. Drawing No.
ENGINE NO. 221-112 DRAWING “A” PARTS LIST Ref. No. Ret, Noe. No, | Part No. Description Used No. | Part No. Description Used, 1 | 291891 | Guide, Front Air @ 36| 68477 Gasket, Fitter Bowl 2 | 22907 Support, Upper Fuel Tank 37 88487 Bowl, Fuel Filter | 22813 Bracket, Fuel Tank 38 ] 99910 Filter Says, Fuel 1 4 | 202415 | Tank, Fuel 39 | 99665 Yoke Says, Fuel Filter 5 § 69221 Cap, Fuel Tank (Screw-on) 40 291655 | Body Says, Upper Carib. 5 | 89961 Cap, Fuel Tank {Bayonet) 41 | 202681 | Needle Valve Says.
ENGINE DRAWING “B” PARTS LIST Ref. No. Ref. No. No. | Part No Description Used No. | Part No. Description Used i 295677 | Housing, Flywheel a0 90700 Cap screw 2 69932 Rope, Starter 31 2016872 | Support Says, Ball Brg. 3 22808 Pulley, Rope Starter 82 250432 | Oil Seal 4 23949 Kut, Flywheel * 33 27374 Gasket, .005" 5 92272 Caseworker & 34 27375 Gasket, 009" & 90366 Lock washer * 35 27349 Gasket, .
ENGINE NO. 221-112 DRAWING “C’ PARTS LIST Ref. No, Ref, No. No. Part No. Description Used No. |Part No. Description Used 1 | 22081 Shield, Cylinder 43 66203 Shaft, Cam 2 | 27352 Gasket 44 | 26670 Tappet, Valve 3 | 210580 Head, Cylinder 45 | 65232 Plug, Cam Shaft 4 | 22068 ‘Washer, Cyl. Head 48 | 291182 | Gear Says, Governor 5 | 92874 Resew, Cyl.