Operator's Manual

ManualsBrandsToro ManualsLawn MowersToro 2615

FormNo.3414-501RevB

HoverPro

450and550Machines

ModelNo.02610—SerialNo.400000000andUp

ModelNo.02611—SerialNo.400000000andUp

Operator'sManual

Introduction

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemical

orchemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orreproductiveharm.

Theengineexhaustfromthisproduct

containschemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orotherreproductiveharm.

ItisaviolationofCaliforniaPublicResourceCode

Section4442or4443touseoroperatetheengineon

anyforest-covered,brush-covered,orgrass-covered

landunlesstheengineisequippedwithaspark

arrester,asdenedinSection4442,maintainedin

effectiveworkingorderortheengineisconstructed,

equipped,andmaintainedforthepreventionofre.

Thismachinedoesnotcomeequippedwitha

sparkarresterstandard.Youmustinstallthe

sparkarresterkitbeforeoperatingthismachinein

California.

TheenclosedEngineOwner'sManualis

suppliedforinformationregardingtheUS

EnvironmentalProtectionAgency(EPA)and

theCaliforniaEmissionControlRegulationof

emissionsystems,maintenance,andwarranty.

Replacementsmaybeorderedthroughtheengine

manufacturer.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.Keepfor

futurereference.

YoumaycontactTorodirectlyatwww.T oro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorT oroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.

g017365

Figure1

1.Modelandserialnumberplate

Writetheproductmodelandserialnumbersinthe

spacebelow:

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

1.Safety-alertsymbol

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3414-501*B

Summary of content (24 pages)

PAGE 1
Form No. 3414-501 Rev B HoverPro® 450 and 550 Machines Model No. 02610—Serial No. 400000000 and Up Model No. 02611—Serial No. 400000000 and Up Operator's Manual Introduction and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
Safety This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. This machine has been designed in accordance with ANSI B71.4-2012. For models with stated engine horsepower, the gross horsepower of the engine was laboratory rated by the engine manufacturer in accordance with SAE J1349.
PAGE 3
– Shut off the engine and wait for all moving parts to stop. During Operating Safety – Disconnect the spark-plug wire from the spark plug when adjusting cutting height. General Safety • Wear appropriate clothing, including eye protection; slip-resistant, substantial footwear; and hearing protection. Tie back long hair and do not wear jewelry. Fuel Safety DANGER • Do not operate the machine while ill, tired, or Fuel is extremely flammable and highly explosive.
PAGE 4
Slope Safety After Operating Safety WARNING General Safety Running the engine on slopes of more than 45 degrees will cause severe engine damage due to a lack of lubrication. Some of the potential damage could include stuck valves, scored pistons, or burned crank bearings. • Clean grass and debris from the machine to help prevent fires. Clean up oil or fuel spills. • Allow the engine to cool before storing the machine in any enclosure.
PAGE 5
Safety and Instructional Decals Important: Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal130-8322 130-8322 1. Use only fuel with an alcohol content by volume under 10%. 3. Do not use fuel with an alcohol content by volume greater than 10%. 2. Read the Operator's Manual for more information on fuel. decal111-9826 111–9826 1.
PAGE 6
decal94-8072 94-8072 1. Warning—cutting/dismemberment hazard of hand or foot, cutting mechanism. g017410 g017410 H295159 1.
PAGE 7
Setup 3. Repeat for the opposite side. 4. Align the holes on the upper handle with the lower handle. 1 Assembling the Handle No Parts Required Procedure 1. Slide 2 bushings into the frame. 1 2 g209291 3 Figure 4 1. Upper handle 4. U-bolt 2. Hand wheel 3. Washer 5. Lower handle 5. Fit the U-bolt through the upper and lower handle and secure it with a washer and a hand wheel. 4 6. Attach the throttle assembly to the outside of the handlebar and secure it with a nut and a pan screw.
PAGE 8
2 3 Installing the Footstop Filling the Engine with Oil No Parts Required No Parts Required Procedure Procedure Secure the footstop to the bolt on the right side of the lower handle using a nut and 2 washers (Figure 6). Important: Your machine does not come with oil in the engine. Before starting the engine, fill the engine with oil. Note: Install the footstop using the lower hole in the footstop as shown in Figure 6. Max. fill: 0.
PAGE 9
Product Overview 4 5 3 g017338 g017338 Figure 8 6 Note: Fill the engine crankcase with oil until the dipstick indicates that the engine-oil level is correct as shown in Figure 7. If you overfill the engine with oil, remove the excess oil as directed in Changing the Engine Oil (page 16). 2 1 7 4. Install the dipstick and hand tighten it securely. 8 Important: Change the engine oil after the 9 first 5 operating hours; change it yearly thereafter. Refer to Changing the Engine Oil (page 16).
PAGE 10
Specifications Model Cutting width Product width 02610 46.5 cm (18-1/2 inches) 57.5 cm (22-1/2 inches) 02611 53.5 cm (21 inches) 63.5 cm (25 inches) Operation Filling the Fuel Tank • For best results, use only clean, fresh, unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). • Oxygenated fuel with up to 10% ethanol or 15% g017340 MTBE by volume is acceptable.
PAGE 11
Adjusting the Cutting Height Checking the Engine-Oil Level Service Interval: Before each use or daily WARNING 1. Move the machine to a level surface. Adjusting the cutting height may bring you into contact with the moving blade, causing serious injury. 2. Remove the dipstick and wipe it with a clean cloth. 3. Insert, but do not screw in, the dipstick into the oil-fill hole. 4. Remove the dipstick and check it. • Shut off the engine and wait for all moving parts to stop. 5.
PAGE 12
Starting the Engine 1. Place the throttle control to the choke position, ensure that the fuel switch is in the ON position. OFF ON g017329 g017346 g017329 g017346 Figure 16 Figure 14 4. Pull the recoil-start handle. 2. Hold the operator-presence control against the handle. Note: If the machine does not start after several attempts, contact an Authorized Service Dealer. 2 1 g017334 g017334 Figure 15 1. Handle 2. Operator-presence control 3.
PAGE 13
Adjusting the Choke Shutting Off the Engine Use the throttle assembly to adjust the choke (Figure 17). Service Interval: Before each use or daily To shut off the engine, release the operator-presence control (Figure 18). Important: When you release the operator-presence control, both the engine and blade should stop within 3 seconds. If they do not stop properly, stop using your machine immediately and contact an Authorized Service Dealer.
PAGE 14
Cutting Grass Operating Tips • Cut only about a third of the grass blade at a time. Do not cut below the highest setting (34 mm or 1.3 inches for Model 02610 or 32 mm or 1.25 inches for Model 02611) unless the grass is sparse or it is late fall when grass growth begins to slow down. Refer to Adjusting the Cutting Height (page 11). General Mowing Tips • Inspect the area where you will use the machine and remove all objects that the machine could throw.
PAGE 15
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 5 hours • Change the engine oil. Before each use or daily After each use Every 100 hours • Check the engine-oil level. • Ensure that the engine shuts off within 3 seconds after releasing the operator-presence control. • Clean grass clippings and dirt from the entire machine.
PAGE 16
Replacing the Air Cleaner Changing the Engine Oil Service Interval: Yearly Service Interval: After the first 5 hours Yearly 1. Press down on the latch tabs on top of the air-cleaner cover (Figure 20). 2 1. Run the engine a few minutes before changing the oil to warm it. 3 Note: Warm oil flows better and carries more contaminants. 1 2. Ensure that the fuel tank contains little or no fuel so that the fuel does not leak when you tip the machine onto its side. 3.
PAGE 17
8. Install the dipstick and hand tighten it securely. Replacing the Blade 9. Dispose of the used oil properly at a local recycling center. Service Interval: Yearly Important: You will need a torque wrench to install the blade properly. If you do not have a torque wrench or are uncomfortable performing this procedure, contact an Authorized Service Dealer. Servicing the Spark Plug Service Interval: Every 100 hours Use an Champion RN9YC spark plug or equivalent.
PAGE 18
Storage with a block of wood, put your weight behind the ratchet or wrench and tighten the bolt securely. This bolt is very difficult to overtighten. Store the machine in a cool, clean, dry place. Preparing the Machine for Storage Cleaning the Machine Service Interval: Before each use or daily After each use WARNING WARNING Fuel vapors can explode. The machine may dislodge material from under the machine housing. • Do not store fuel more than 30 days. • Wear eye protection.
PAGE 19
Troubleshooting Problem The engine does not start. Possible Cause 1. The wire is not connected to the spark plug. 1. Connect the wire to the spark plug. 2. The hole in the fuel-cap vent is plugged. 3. The spark plug is pitted, fouled, or the gap is incorrect. 2. Clean the hole in the fuel-cap vent or replace the fuel cap. 3. Check the spark plug and adjust the gap if necessary. Replace the spark plug if it is pitted, fouled, or cracked. 4. Drain and/or fill the fuel tank with fresh fuel.
PAGE 20
Notes:
PAGE 21
Notes:
PAGE 22
Notes:
PAGE 23
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
PAGE 24
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).