Form No. 3326-667 Tru Trak Sulky Proline Mid Size Mower Attachment Model No.
Contents For your convenience, write the product model and serial numbers in the space below. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the Axle . . . . . . . . . . . . . . . . . . . . . . . . Installing the Sulky Assemblies . . .
• Do not allow use of the sulky by untrained operators. • Use caution when riding the sulky over curbs, rocks, roots, or other obstructions. • Use appropriate personal protective apparatus for eyes, ears, feet, hands, and head. • Slow down before making turns and use extra caution on rough terrain and on slopes. • Practice operating the machine without the sulky until familiar with the controls. • Travel across slopes, avoiding operation on steep slopes.
1 2 3 1 2 1 1 2 3 3 5 3 4 4 m–5483 Figure 3 1. Front holes (pistol grip machines) 2. Middle holes 2 3. Rear holes (T–bar machines) 4. Axle mounting bracket m-5473 Figure 2 1. Pulley guard 2. Axle 3. Bolts, 3/8 x 1-3/8 in. Installing the Axle on a Gear Drive Machine with a T-bar Control 4. Locknut, 3/8 in. 5. Axle mounting bracket 1. Stop the engine, wait for all moving parts to stop, and remove the ignition key. 2.
1 1 5 7 6 6 5 3 4 4 2 m-5471 3 Figure 4 1. 2. 3. 4. Pulley guard Axle mounting bracket Large spacer Bolts, 3/8 x 1-3/8 in. 5. Locknut, 3/8 in. 6. Bolt, 3/8 x 4-1/2 in. 7. Small spacer m–5476 2 3. Remove the long bolt and nut securing the top of each pulley guard (Fig. 4) and discard the bolt. 4. Insert the axle mounting brackets between the pulley guards and the frame (Fig. 4). 6 5 5. Insert the large spacers between the axle mounting brackets and the frame, lining up the holes (Fig. 4).
4. Using the 6 bolts (3/8 x 1-3/8 in.) and locknuts (3/8 in.) supplied with the sulky, secure the axle and the spacers as illustrated in Figure 5. 2. Secure the sulky assemblies using a washer (1-3/4 in.) and lynch pin on each side (Fig. 7). 3. Grease the sulky; refer to Greasing the Sulky, page 8. Note: You may have difficulty installing one of the bolts on the right side due to interference with the traction control lever. If this happens, disconnect the control rod from the pistol grip (Fig.
• If your machine is a gear drive, pistol grip machine, you may need to adjust the wheel drive tension; refer to you machine Operator’s Manual. Important The sulky must be at least 1-1/2 in. (3.8 cm) from any contact point such as the machine handle or the gear shift lever (when pushed to the right and left) on gear drive machines. Position the hook so that it is as close to horizontal as possible. Positioning the Sulky for Transport 4.
Maintenance Recommended Maintenance Schedule Maintenance Service Interval Maintenance Procedure 8 hours • Check the tire pressure. 25 hours • Grease all fittings. • Grease all fittings. • Check the tire pressure. • Paint chipped surfaces. Storage Service Checking Tire Pressure Ensure that the caster wheel tires are filled with air to 50 psi (345 kPa) every 8 operating hours or before each use. Greasing the Sulky Grease all grease fittings every 25 operating hours and immediately after every washing.
