Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 30118

 2004 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

32in Recycler



Kit

for Fixed Deck Mid–Size Mowers

Model No. 30118

Form No. 3350-108

Installation Instructions

Loose Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Baffle

Bolt, 5/16 x 5/8 inch

Flange nut, 5/16 inch

Install the Recycler



baffle

Blocker plate

Bolt, 3/8 x 1 inch

Flange nut, 3/8 inch

Bolt, 1/4 x 3/4 inch

Flange nut, 1/4 inch

Install the blocker plate

Cover plate

Bolt, 3/8 x 3/4 inch

Flange nut, 3/8 inch

Install the cover plate

Kicker

Bolt, 5/16 x 5/8 inch

Flange nut, 5/16 inch

Install the kickers

Recycler



blade 2 Replace standard blades on mower

Preparing the Mower

1. Remove belt cover from top of mower.

2. Thoroughly clean underside of the mower. All debris

must be removed to ensure that baffles and kickers will

fit properly against the cutting chamber.

3. Tilt the mower up and support with jack stands to ease

installation of kit.

4. Flip up discharge chute and remove the discharge baffle

near discharge opening (Fig. 1).

Note: Replace hardware in top of mower when baffle is

removed for safety and to save for use when using mower

to side discharge.

Summary of content (4 pages)

PAGE 1
32in Recycler Form No. 3350-108 Kit for Fixed Deck Mid–Size Mowers Model No. 30118 Installation Instructions Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY.
PAGE 2
Warning 1 Open holes in the mower exposes you and others to thrown debris. Debris thrown out of holes in the mower can cause injury. 3 • Never operate mower without hardware mounted in all holes in mower. • Install hardware in mounting holes when mulching baffle is removed. 1 2 m–3924 2 Figure 2 1. Baffle 2. Flange nut 5/16 inch 3. Bolt, 5/16 x 5/8 inch (16 mm) Installing the Blocker Plate m–3923 1. Place the blocker plate inside cutting chamber between the front and baffle. Figure 1 2.
PAGE 3
Installing the Kickers 4 1. Measure from the spindle center lines, and locate kickers as shown (Fig. 5). Position one kicker 7/16 inch (11 mm) off to the right of the right spindle and one kicker 1-7/8 inch (48 mm) off to the left of the left spindle (Fig. 5). 1 2. Holding kickers tight against baffle, mark, center punch and drill 2 holes (11/32 inch) holes for each kicker (Fig. 5). 1 (right) 2 (left) 2 m–3925 5 Figure 3 1. Blocker plate 2. Bolt, 3/8 x 5/8 inch 3. Flange nut, 3/8 inch 4.
PAGE 4
Installing the Recycler Blades Removing Baffles for Side Discharge Cutting Warning 1. Thoroughly clean the mower. A blade is sharp. Contact with sharp blade can cause serious personal injury. 2. Tilt the mower up and support with jack stands to ease removal of kit. • Wear gloves or wrap sharp edges of the blade with a rag. 3. Remove the mounting hardware from the baffle, blocker plate, kickers and discharge cover plate. Note: Save the hardware for use when installing the baffle. 1.