%5 / !2241% -!7)-4- 2!&%38 /03)-4- 0%1&/1-!.#% !.$ 3/ '!). +./6,%$'% /& 3(% 01/$4#3 )3 )2 %22%.3)!, 3(!3 8/4 /1 !.8 /3(%1 /0%1!3/1 /& 3(% -/6%1 1%!$ !.$ 4.$%123!.$ 3(% #/.3%.32 /& 3()2 -!.4!, "%&/1% 3(% %.').% )2 %5%1 23!13%$ !8 0!13)#4,!1 !33%.3)/. 3/ 3(% ()'(,)'(3%$ "8 3()2 28-"/, 9 (% #/.&/1-2 3/ 3(% -%1)#!. !3)/.!, 3!.$!1$2 .23)343% 2 2!&%38 23!.
The GROUNDSMASTER 1000L was developed to satisfy the demand for a maneuverable, intermediate size, turf maintenance rotary mower. The machine has advanced concepts in engineering, design and safety; and if maintained properly, it will give excellent service. Since the GROUNDSMASTER 1000L is a high quality product, Toro is concerned about the future use of the machine and the safety of the user. Read this manual to familiarize yourself with the proper set up, operation, and maintenance instructions.
# # Air Cleaner Maintenance . . . . . . . . . . . . . . . . . . 23 Cleaning Radiator, Oil Cooler And Screen . . . 23 Changing Engine Oil And Filter . . . . . . . . . . . .
! )& 6"2 3&23&% ".% $&13*'*&% #7 '/1 $/-0,*".$& 6*3) 3)& 9 20&$*'*$"3*/.2 /' 3)& -&1*$". "3*/.", 3".%"1%2 .23*343& ,3)/4() )"8"1% $/.31/, ".% "$$*%&.3 01&5&.3*/. 0"13*",,7 "1& %&0&.%&.3 40/. 3)& %&2*(. ".% $/.'*(41"3*/. /' 3)& -"$)*.& 3)&2& '"$3/12 "1& ",2/ %&0&.%&.3 40/. 3)& "6"1&.&22 $/.$&1. ".% 01/0&1 31"*.*.( /' 3)& 0&12/..&, *.5/,5&% *. 3)& /0&1"3*/. 31".20/13 -"*.3&.".$& ".% 23/1"(& /' 3)& -"$)*.& -01/0&1 42& /1 -"*.3&.".
! This product may exceed noise levels of 85 dB(A) at the operator position. Ear protectors are recommended for prolonged exposure to reduce the potential of permanent hearing damage. Using the machine demands attention and to prevent loss of control: A. Operate only in daylight or when there is good artificial light. B. Drive slowly. Avoid sudden stops and starts. C. Watch for holes or other hidden hazards. D. Look behind machine before backing up. E.
!& ! " ! The following safety and instruction decals are affixed to the traction unit. If any decal becomes illegible or damaged, install a new decal. Part numbers are listed below and in your Parts Catalog.
SPECIFICATIONS Engine: Manufacturer Ċ Kawasaki Horsepower Ċ 20 @ 3600 RPM. Displacement Ċ 617 cc. Crankcase Capacity Ċ 1.6 qts. w/filter. Governor Ċ Mechanical. Governor Limit Ċ 3350Ć3550 RPM. Idle Speed Ċ 1500 RPM. Air Cleaner: Kawasaki duel element filter. Fuel Tank Capacity: 8.5 gal. Fuel Filter: Replaceable inline type. Fuel Pump: 12 volt electric (transistor type). Cooling System: Radiator Ċ Approx. 4 qt. capacity. Expansion Tank Ċ Remote mounted; 1/2 qt. capacity.
Use this chart as a checklist to assure all parts have been received. Without these parts, total set-up cannot be completed. Steering Wheel Nut Screw Cap 1 1 1 1 Seat Assembly Clevis Pin Cotter Pin 3/4 x 3/4" lg. Flat Washer Cotter Pin 1/8 x 1" lg. 1 2 2 1 1 Install Seat Assembly Roll Pin Capscrew 5/16 Ć 18 x 1-3/4 in. Locknut 5/16 Ć 18 1 2 2 Secure universal shaft to implement. Cylinder Pin Cotter Pin 3/16 x 1-1/2 in.
0*&1"-. ( .% #/ &. // %"! /+ /- /&+* 0*&/ #- )" 2&/%+0/ #&-./ -"4 )+1&*$ 0*&1"-. ( .% #/ +- +0,(&*$ &/ /+ .0&/4 (" &),(")"*/ Remove steering wheel from seat plate. Remove screw and cap from steering wheel (Fig.1). Remove jam nut from steering shaft. Make sure foam seal is on steering shaft (Fig.1). Slide steering wheel onto steering shaft. &$0-" " / ..
SET-UP INSTRUCTIONS 5. Adjust seat to desired operating position. Loosen adjustment handles, slide seat fore or aft in slotted holes and tighten adjustment handles to secure in place. INSTALL OPTIONAL SUSPENSION SEAT Model 30239 1. Remove seat and seat springs from seat base. 2. Mount each seat adapter bracket to seat with (2) 5/16-18 x 3/4" lg. capscrews, flatwashers and lockwashers, positioning as shown in figure 5. 9.
SET-UP INSTRUCTIONS INSTALL REAR WEIGHT Two Wheel Drive Groundsmaster 1000 Series Traction Units comply with ANSI B71.4-1990 Standard when equipped with rear weight. 35 lbs. of rear weight is installed, at the factory, on the Groundsmaster 1000L Traction Unit. Use chart below to determine combinations of additional weight requirements. Order parts from your local Authorized Toro Distributor. Additional Rear Weight Required Left Side Weight Required Weight Part Number Weight Description Qty.
–20 C –10 C 0 C 10 C 20 C The engine is shipped with 1.6 qt. of oil in the crankcase; however, level of oil must be checked before and after the engine is first started. 30 C 40 C SAE 40 Position machine on a level surface. SAE 30 Open the hood. Remove dipstick and wipe it with a clean rag. Insert dipstick into the tube and make sure it is fully seated. Remove dipstick and check level of oil (Fig. 7). If oil level is low, remove oil fill cap (Fig.
' &.(*.& )"2 #&&. 14..*.( 01&2241*9&% )/3 $//,".3 $". &2$"0& 6)&. 1"%*"3/1 $"0 *2 1&: -/5&% ".% $"42& #41.2 *(41& "%*"3/1 $"0 70".2*/. 3".+ $"0 /3& Do not mix engine oil and automatic transmission fluid or hydraulic component damage may result. When changing fluids, also change transmission filter. The axle housing acts as the reservoir for the system.
" " ! " NEVER USE METHANOL, GASOLINE CONTAINING METHANOL, GASOLINE CONTAINING MORE THAN 10% ETHANOL, GASOLINE ADDITIVES, PREMIUM GASOLINE OR WHITE GAS BECAUSE ENGINE
+/$ + % , (Fig. 13) Ċ The left and right brake pedals are connected to the left and right front wheels. Since both brakes work independently of each other, the brakes can be used to turn sharply or to increase traction if one wheel tends to slip while operating on certain slope conditions. However, wet grass or soft turf could be damaged when brakes are used to turn sharply. To make a quickĆstop", depress both brake pedals together.
$ ( ' $ (Fig. 15) ĊThe ignition switch, which is used to start and stop the engine, has three positions: OFF, RUN and START. Rotate key clockwise Ċ START position Ċ to engage starter motor. Release key when engine starts. The key will move automatically to the ON position. To shut engine off, rotate key counterclockwise to the OFF position. (Fig. 15) Ċ To start engine, close carburetor choke by pulling choke control upward.
Ensure parking brake is set, PTO switch is in OFF position and lift lever is in TRANSPORT or FLOAT position (Fig. 15). Remove foot from traction pedal and insure it is in neutral. Pull choke (Fig. 15) to full choke position and move throttle control (Fig. 15) to slow position. Turn key in ignition switch to START position (Fig. 15). Release key immediately when engine starts and allow it to return to RUN position.
!,0 /! -! - 2!%#$/ %. )! !.. -3 /* +-!1!)/ /$! -! - 2$!!'. "-*( '! 1%)# /$! #-*0) * )*/ ./*+ .0 !)'3 2$%'! 0//%)# 0)%/ *- %(+'!4 (!)/ %. - %.! * )*/ /- 1!' *2) $%'' 2%/$ /$! 0//%)# 0)%/ *- %(+'!(!)/ - %.! " /$! -! 2$!!'. '! 1! /$! #-*0) ./!!-%)# %. '*./ This product may exceed noise levels of 85 dB(A) at the operator position. Ear protectors are recommended for prolonged exposure to reduce the potential of permanent hearing damage.
The traction unit has grease fittings that must be lubricated regularly with No. 2 General Purpose Lithium Base Grease. If machine is operated under normal conditions, lubricate all bearings and bushings after every 50 hours of operation or whenever water is used to clean machine. Bearings and bushings must be lubricated daily when operating conditions are extremely dusty and dirty.
" ! # ! " $ "
(duplicate this page for routine use) Daily Maintenance Check For Week Of ___________ Maintenance C Check Item b MON n Safety Interlock Operation n Grass Deflector in Down Position n Brake Operation n Engine Oil Level n Cooling System Fluid Level n Air Filter n Radiator & Screen for Debris n Unusual Engine Noises n Transmission Oil Level n Hydraulic Hoses for Damage n Fluid Leaks n Tire Pressure n Instrument Operation n Condition of
Clean air cleaner foam element after every 50 operating hours. More frequent cleaning is required when mower is operated in dusty or dirty conditions. Remove wing nuts securing air cleaner cover to air cleaner and remove cover (Fig. 25). Clean cover thoroughly . Reinstall foam element, paper element and air cleaner cover. * )*. *+", ." ")#%)" 1%.$*/. %, '" )", "'"("). " /-" "2.,"(" ")#%)" 1" , )! ! ( #" 1%'' '%&"'3 ,"-/'.
MAINTENANCE 5. Remove and replace oil filter (Fig. 28); refer to parts catalog for part number. 1 5. Tighten clamps. CHECKING AND REPLACING SPARK PLUGS Since air gap between center and side electrodes increases gradually during normal engine operation, check condition of electrodes at 100 hour intervals. The correct spark plugs to use in the engine are NGK BMR 6A or equivalent. Set air gap at .024-.028 in. 1. Clean area around spark plugs so dirt does not fall into cylinder when plugs are removed. 2.
! After setting air gap at .024-.028", install spark plug in cylinder head. Tighten plugs to 17 ft-Ib. Push wires onto spark plugs. Remove bolt and nut securing nylon block and remove nylon block (Fig. 33). # ! ! Check tension of belt initially after the first day of operation and every 100 hours thereafter. !3 ,)'/ !)26-32 Turn engine off and remove the ignition key. Set the parking brake. Raise the engine hood and allow the engine to cool.
The machine must not creep when traction pedal is released. If it does creep, an adjustment is required. Park machine on a level surface and shut engine off. Depress only the right brake pedal and engage the parking brake. Jack up left front side of machine until tire is off shop floor. Support machine with jack stands to prevent it from falling accidentally. Lift seat.
)'30% !, -321 %&.0% 5%+$)-' .- 2(% ,!#()-% $)1#.--%#2 '0.3-$ #!"+% &0., 2(% "!22%06 2. /0%4%-2 $!,!'% 2. 2(% %+%#20)#!+ 1612%, )'30% 6$0!3+)# 1612%, &)+2%0 6$0!3+)# 0%230- +)-%1 3#2).- +)-% Adjust the service brakes when there is more than one inch of free travel" of the brake pedals, or when the brakes do not work effectively.
WHITE RED FUSIBLE LINK REG. CONN. 1 4 2 5 3 4 1 6 5 2 10 AMP FUSE STARTER BATTERY F3 BLACK B 6 ENGINE 3 CONN. F4 RED ENGINE BLOCK GROUND SPARE RED ORANGE SPARE BLACK 30 AMP ATO/ATC SP2 15 AMP FUSE YELLOW FUSE BLOCK RED WHITE GRAY OVER TEMP. RELAY (ENERGIZED) ORANGE N.O. N.C. VIOLET/RED LIGHT BLUE YELLOW DARK GREEN VIOLET WHITE IGNITION SWITCH BROWN BA I PTO SWITCH (OFF) SEAT SW. (UNOCCUPIED) VIOLET/RED SY X DARK BLUE GREEN/BLACK N.O.
HYDROSTATIC TRANSMISSION & CHARGE PUMP 800 PSI 70-150 PSI LIFT CYLINDERS 4 GAL/MIN .
' )"%$ $") Thoroughly clean the traction unit, cutting unit and the engine, paying special attention to these areas: - radiator and radiator screen - underneath the cutting unit - under the cutting unit belt covers - counterbalance springs - P.T.O. Shaft Assembly - all grease fittings and pivot points - remove control panel and clean out inside of the control box - beneath seat plate and top of transmission Check the tire pressure.
! Check Battery Fluid Level Check Battery Cable Connections Lubricate All Grease Fittings Lubricate Brake Cables Check Cutting Unit Gear Box Oil Level Clean Under Cutting Unit Belt Covers Check Cutting Unit Drive Belt Adjustment } Change Engine Oil Service Air Filter ! ! Every 50hrs Every 100hrs Every 200hrs Every 400hrs } Change Engine Oil Filter Check Electric Clutch Gap Adjustment { Check PTO Belt T
A OneĆYear Limited Warranty (A TwoĆYear Full Warranty for Residential Use) LCG What Is Covered By This Express Warranty? What Must You Do To Keep The Warranty In Effect? The Toro Company promises to repair any TORO product used for commercial, institutional, or rental purposes if defective in materials or workmanship for a period of one year from the date of purchase. The cost of parts and labor are included, but the customer pays the transportation cost.
