Installation Instructions

ManualsBrandsToro ManualsRiding ProductsCE Guard Kit, Groundsmaster 3280-D Traction Unit

FormNo.3402-903RevA

CEGuardKit

Groundsmaster

3280-DTractionUnit

ModelNo.30215

InstallationInstructions

Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Safety

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

CAUTION

Thismachineproducessoundlevelsinexcessof85

dBAattheoperator’searandcancausehearingloss

throughextendedperiodsofexposure.

Wearhearingprotectionwhenoperatingthis

machine.

SoundPowerLevel

Thisunithasaguaranteedsoundpowerlevelof105dBA,

whichincludesanUncertaintyValue(K)of1dBA.

Soundpowerlevelwasdeterminedaccordingtothe

proceduresoutlinedinISO11094.

SoundPressureLevel

Thisunithasasoundpressurelevelattheoperator’searof

90dBA,whichincludesandUncertaintyValue(K)of1dBA.

Soundpressurelevelwasdeterminedaccordingtothe

proceduresoutlinedinENISO5395:2013.

VibrationLevel

Hand-Arm

Measuredvibrationlevelforrighthand=1.25m/s

Measuredvibrationlevelforlefthand=1.28m/s

UncertaintyValue(K)=0.5m/s

Measuredvaluesweredeterminedaccordingtotheprocedures

outlinedinENISO5395:2013.

WholeBody

Measuredvibrationlevel=0.37m/s

UncertaintyValue(K)=0.5m/s

Measuredvaluesweredeterminedaccordingtotheprocedures

outlinedinENISO5395:2013.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3402-903*A

Summary of content (12 pages)

PAGE 1
Form No. 3402-903 Rev A CE Guard Kit Groundsmaster® 3280-D Traction Unit Model No. 30215 Installation Instructions Determine the left and right sides of the machine from the normal operating position. Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 106-6754 1. Warning—do not touch the hot surface. 2. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay away from moving parts. 131-3393 131-1944 1. Read the Operator's Manual. 2 4. Do not drive across or down slopes greater than 14 degrees. 1.
PAGE 3
108-6585 (Apply over 114-2855 for CE machines) * This safety decal includes a slope warning required on the machine for compliance to the European Lawn Mower Safety Standard EN ISO 5395:2013. The conservative maximum slope angles indicated for operation of this machine are prescribed by and required by this standard. 1. Warning—read the Operator's Manual, all operators should be trained before operating the machine. 3. Cutting/dismemberment hazard of hands or feet, mower blade—stay away from moving parts.
PAGE 4
Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Qty.
PAGE 5
1. Attach the guard mount to the fuel-tank support bracket using 2 bolts (1/4 x 3/8 inch) as shown in Figure 2. 1 Installing the Gearbox Guards Parts needed for this procedure: 1 Guard mount 1 Gearbox guard 1 Joint guard 1 Drive-assembly guard 3 Nut (1/4 inch) 2 Shoulder bolt 2 Spring washer 1 Spacer 1 Washer (9/32 inch) 1 Bolt (1/4 x 5/8 inch) 4 Bolt (3/8 x 1/2 inch) 2 Bolt (1/4 x 3/8 inch) Figure 2 1. Fuel-tank support bracket 3. Bolt (1/4 x 3/8 inch) 2. Guard mount 2.
PAGE 6
3. Attach the joint guard to the gearbox guard using 2 shoulder bolts, 2 spring washers, and 2 nuts (1/4 inch) as shown in Figure 4. 2 Installing the PTO Guards Parts needed for this procedure: Figure 4 1 Left PTO guard 1 Right PTO guard 1 Grommet 2 Bolt (3/8 x 7/8 inch) 2 Washer (7/16 inch) 2 Locknut (3/8 inch) 2 Bolt (5/16 x 1/2 inch) 1. Nut (1/4 inch) 4. Joint guard 4 Washer (3/8 inch) 2. Spring washer 5.
PAGE 7
5. Attach the front of the left PTO guard to the left side of the machine using 2 bolts (5/16 x 3/4 inch), 2 washers (3/8 inch), and 2 nuts (5/16 inch) as shown in Figure 8. 1. If you have a 4-wheel-drive model, insert the grommet into the right PTO guard (Figure 7). Figure 7 1. Bolt (5/16 x 1/2 inch) 4. Washer (7/16 inch) 2. Washer (3/8 inch) 5. Locknut (3/8 inch) 3. Grommet (4-wheel-drive only) 6. Bolt (5/16 x 3/4 inch) Figure 8 1. Washer (3/8 inch) 4. Bolt (5/16 x 1/2 inch) 2.
PAGE 8
. Use the table below to select the correct tipping-hazard-warning decal for your machine from decal 131-1944. Model 30366 Model 30366+30348 Model 30403 Model 30551 Model 30404 Model 31335 Model 31336 60-inch base deck 62-inch base deck 62-inch SDD 72-inch base deck 72-inch 4-castor base deck 72-inch SDD SDD SDD Guardian Guardian/RDD Model 30344 (2-wheeldrive) C C C E D C B Model 30345 (4-wheel drive) D D C E B B N/A Guardian/RDD Guardian/RDD 9.
PAGE 9
1. Select the axle guard for either the 2-wheel-drive or 4-wheel-drive machine (Figure 13). 4 Installing the Hood Latch Parts needed for this procedure: 1 Lock assembly 1 Hood latch 2 Bolt (1/4 x 3/4 inch) 4 Washer (9/32 inch) 2 Locknut (1/4 inch) 1 Safety decal (106-6754) Procedure 1. Open the hood. 2. Attach the hood latch to the radiator frame using the provided fasteners (Figure 14). Figure 13 1. Bolt (3/8 x 7/8 inch) 3. 2-wheeldrive axle guard 2. Bolt (1/4 x 3/8 inch) 4.
PAGE 10
4. Insert the lock assembly and washer into the hole on the hood and secure it underneath with the nut (Figure 15). Note: Ensure that the lock is correctly oriented. Figure 15 1. Decal 106-6754 2. Nut 3. Washer 4. Lock assembly 5. Apply the decal to the hood next to the latch (Figure 15).
PAGE 11
Notes: 11
PAGE 12