Installation Instructions

ManualsBrandsToro ManualsRiding ProductsCE Kit, Groundsmaster 7200 or 7210 Traction Unit

FormNo.3431-395RevA

CEKit

Groundsmaster

7200or7210TractionUnit

ModelNo.30240

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Safety

SafetyandInstructionalDecals

Note:Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedormissing.

decal138-8202

138-8202

Note:Thismachinecomplieswiththeindustrystandard

stabilitytestinthestaticlateralandlongitudinaltestswiththe

maximumrecommendedslopeindicatedonthedecal.Reviewthe

instructionsforoperatingthemachineonslopesintheOperator’s

Manualaswellastheconditionsinwhichyouwouldoperatethe

machinetodeterminewhetheryoucanoperatethemachineinthe

conditionsonthatdayandatthatsite.Changesintheterraincan

resultinachangeinslopeoperationforthemachine.Ifpossible,

keepthecuttingunitsloweredtothegroundwhileoperatingthe

machineonslopes.Raisingthecuttingunitswhileoperatingon

slopescancausethemachinetobecomeunstable.

1.Tippinghazard—donot

drivethemachineona

slopegreaterthan16

degrees.

3.Tippinghazard—donot

drivethemachineona

slopegreaterthan18

degrees.

2.Tippinghazard—donot

drivethemachineona

slopegreaterthan17

degrees.

4.ReadtheOperator's

Manual.

decal138-8200

138-8200

1.ReadtheOperator'sManual.

decal106-6754

106–6754

1.Warning—donottouchthe

hotsurface

2.Cutting/dismemberment

hazard,fanand

entanglementhazard,

belt—stayawayfrom

movingparts.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3431-395*A

Summary of content (12 pages)

PAGE 1
Form No. 3431-395 Rev A CE Kit Groundsmaster® 7200 or 7210 Traction Unit Model No. 30240 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Safety Safety and Instructional Decals Note: Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal138-8200 138-8200 1. Read the Operator's Manual.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 Description Use Qty.
PAGE 3
2 Installing the Hood-Lock Assembly Kubota Models Parts needed for this procedure: 1 Latch support 1 Latch bracket 1 Lock assembly 1 Bolt (5/16 x 3/4 inch) 2 Bolt (5/16 x 2 inches) 3 Locknut (5/16 inch) Procedure 1. Locate the upper (rear) metal frame support running across the underside of the hood. 2. In the upper, left corner of the metal frame, locate the hole drilled in the face of the support. 3. Using a 5/16-inch bit, drill open the hole. 4.
PAGE 4
g004787 Figure 1 1. Hole in the metal frame support 4. Bolt (5/16 x 3/4 inch) 2. Locknut (5/16 inch) 5. Lock assembly 3. Latch support 6.
PAGE 5
13. Install the latch bracket to the left frame member, directly below the lock assembly, in the existing holes, as shown in Figure 2. 3 Note: Center the bolts in the slots of the latch Installing the Hood-Lock Assembly bracket. Yanmar Models Parts needed for this procedure: g030830 Figure 2 1. Left frame member 2. Locknut (5/16 inch) 14. 15. 3. Latch bracket 4.
PAGE 6
8. Remove the punch-out from the latch support. 14. 9. Install the latch support to the frame (Figure 3). Close the hood slowly to verify that the latch catches. 10. Remove the locking nut from the lock assembly. Note: If the latch does not catch, loosen the 11. Install the lock assembly through the hood and the support latch bracket with the catch facing forward (Figure 4). bolts securing the latch bracket to the frame member and adjust the bracket as necessary.
PAGE 7
2. Install the floor-plate latch to the frame using 2 carriage bolts (1/4 x 3/4 inch) and 2 locknuts (1/4 inch) (Figure 6). 3. Remove the 2 locking nuts from the lock assembly. 4. Insert the lock assembly into the hole in the floor plate with the catch facing to the left. 5. Install the locking nuts onto the bottom of the lock assembly to secure it in place. Note: The mounting holes in the latch are slotted so that you can adjust the lock assembly.
PAGE 8
g004788 Figure 7 1. Hood 5. Washer (5/16 inch) 2. Distance from the support edge—3.81 cm (1-1/2 inches) 6. Bolt (1/4 x 1-1/8 inch) 3. Drilled hole 7. Distance between the holes—12.2 cm (4-13/16 inch) 4.
PAGE 9
6 7 Securing the Belt Covers Securing the Seat Plate Parts needed for this procedure: Parts needed for this procedure: 2 Bolt (5/16 x 1-1/4 inches) 2 Retaining nut (5/16 inch) 2 Push nut 1 Bolt (5/16 x 1-1/4 inches) Procedure 1. 2. Procedure Install a bolt in the seat plate to the secure it. Locate the hole in the front, right side of the seat plate, in front of the manual housing. Install a bolt (5/16 x 1-1/4 inches) in the hole to secure the seat plate (Figure 9). 3.
PAGE 10
Note: For each decal, peel off the backing and squeegee across the surface of the decal, starting at the center of the decal and working toward the edges, using overlapping strokes. A. Install decal 106-6754 onto the hood as shown in Figure 10. g004789 Figure 10 1. Decal 106-6754 3. Lock assembly 2. Hood 4. Decal location B.
PAGE 11
Selecting the Sound and Angle Decals Note: Use the following tables to determine the proper sound and angle decals to put on the machine after the kit has been installed.
PAGE 12
Angle Information A B C 16 Degrees 17 Degrees 18 Degrees 2015 and After Model-Number Configurations 30354 30353 30457 30456 31101 72-inch SDD 72-inch base 62-inch base 60-inch SDD 100-inch RD 30495/TC GM7200 1105 Kubota C C C B — 30487/TC/TE GM7210 1105T Kubota C C C B A 30695 GM7210 T4 A A A A A Pre-2015 Model-Number Configurations 30360TE GM7200 72-inch SDD - CE deck C C C B 30363TE GM7210 72-inch SDD - CE deck C C C B 30461 GM7200 <25hp 72-inch base deck