Installation Instructions

ManualsBrandsToro ManualsAttachmentsSpeed Reduction Kit, 2015 and After Groundsmaster 360 Multi-Purpose Machine

FormNo.3395-831RevA

SpeedReductionKit

2015andAfterGroundsmaster

360Multi-PurposeMachine

ModelNo.30287

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachinebeforeinstalling

thekit.

Hydrauliccylinder1

Hydraulictting(90degree)

Hydraulictting(45degree)

Jamnut(3/8inch)

Brake-linkageyolk1

Preparethecylinderbeforeinstalling

thekit.

Cylindersupport

Jamnut1

Yolklinkage1

Clevispin

Spring-clevispin

Locking-cotterpin1

U-bolt2

Nut(3/8)

Mountthecylindertotheframe.

Shorthydraulichose

Longhydraulichose1

Hydraulictting(straight)

Cabletie

Connectthehosestothehydraulic

system.

Nopartsrequired

–

Installtherearwheelstothetraction

unit.

Nopartsrequired

–

Adjusttheoperationofthe

speed-reductionunit.

Nopartsrequired

–

Completetheinstallation.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3395-831*A

Summary of content (8 pages)

PAGE 1
Form No. 3395-831 Rev A Speed Reduction Kit 2015 and After Groundsmaster® 360 Multi-Purpose Machine Model No. 30287 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 Description Qty. Use Prepare the machine before installing the kit.
PAGE 2
WARNING Hydraulic fluid escaping under pressure can penetrate skin and cause injury. • Make sure that all hydraulic fluid hoses and lines are in good condition and that all hydraulic connections and fittings are tight before applying pressure to the hydraulic system. • Keep your body and hands away from pin-hole leaks or nozzles that eject high-pressure hydraulic fluid. • Use cardboard or paper to find hydraulic leaks.
PAGE 3
Figure 4 1. 70 degree Figure 2 1. Hydraulic fitting (90 degree) Installing the Connecting Pin 3. Hydraulic fitting (45 degree) 1. Install the jam nut (3/8 inch) to the cylinder rod until it is 2.22 cm (0.875 inch) from the end (Figure 5). 2. Hydraulic cylinder 2. Torque the fitting to 20 to 26 N-m (15 to 19 ft-lb). 3. Aim the open end of the fitting along the axis of the cylinder body (Figure 3). Figure 5 Figure 3 1. Cylinder rod 3. 2.22 cm (0.875 inch) 2. Jam nut (3/8 inch) 4.
PAGE 4
3 Mounting and Adjusting the Cylinder to the Frame Parts needed for this procedure: 1 Cylinder support 1 Jam nut 1 Yolk linkage 1 Clevis pin 1 Spring-clevis pin 1 Locking-cotter pin 2 U-bolt 4 Nut (3/8) Figure 8 Installing the Cylinder Mount to the Frame 1. Locking-cotter pin 3. Yolk linkage 2. Clevis pin 4. Traction lever 3. Arrange the holes in the yolk linkage around the slot in the traction lever (Figure 8). 1.
PAGE 5
Figure 11 Figure 10 1. 2.2 cm (0.86 inch) 1. Threaded plug 2. Hydraulic manifold 2. 33 cm (13 inch) 2. Connect the hydraulic fitting (straight) at the location you removed the threaded plug from on the hydraulic transmission. 7. Tighten the 4 flange nuts to secure the mounting bracket to the frame (Figure 7). Note: Ensure that the O-rings are in position and lubricated with hydraulic oil before installing the fitting. 4 3. Torque the hydraulic fitting (straight) to 12 to 14 N-m (9 to 11 ft-lb).
PAGE 6
Figure 13 1. Hydraulic cylinder 2. Short hydraulic hose Figure 15 7. Connect the hose fitting (straight) on the short hydraulic hose to the hydraulic fitting (45 degree) on the hydraulic cylinder (Figure 14). 1. Left, rear-wheel hub Note: Ensure that the O-rings are in position and lubricated with hydraulic oil before connecting the hose. 2. Hose fitting (90 degree 2. Connect the hose fitting (90 degree) on the long hydraulic hose to the hydraulic fitting on the hydraulic line (Figure 16).
PAGE 7
Figure 17 1. Hydraulic cylinder Figure 19 2. Long hydraulic hose 5. Connect the hose fitting (straight) on the long-hydraulic hose to the hydraulic fitting (90 degree) on the hydraulic cylinder (Figure 18). Note: Ensure that the O-rings are in position and lubricated with hydraulic oil before connecting the hose. Figure 18 1. Hose fitting (straight) 2. Hydraulic fitting (90 degree) 6. Torque the fitting to 20-26 N-m(15 to 19 ft-lb). 7. Secure the hydraulic hoses with the cable ties (Figure 19).
PAGE 8
5 Installing the Rear Wheels No Parts Required Procedure 1. Install the rear-wheel to the traction unit and hand-tighten the lug nuts. 2. Torque the lug nuts to 101 to 115 N-m (75 to 85 ft-lb) in the following order (Figure 20). Figure 21 • Loosen the jam nut on the cylinder rod (Figure 6). • Rotate the yoke in on the cylinder rod to increase the mowing speed. • Rotate the yoke out on the cylinder rod to decrease the mowing speed. Note: The speed range of the adjustment is 6.4 to 19.3 km/h (4 to 12 mph).