Form No. 3437-182 Rev B 60in, 62, or 72in Rotary Mower Groundsmaster® 360 Series and 7200 Series Traction Unit Model No. Model No. Model No. Model No. Model No. Model No. Register at www.Toro.com. Original Instructions (EN) CV 30353—Serial No. 30353—Serial No. 30456—Serial No. 30457—Serial No. 30481—Serial No. 30481—Serial No.
Model 30456 complies with all relevant European directives when the CE Kit (Model 30658) is installed on the cutting unit. Model 30353 requires CE Kit Model 30685; 30457 requires CE Kit 30683; 30481 requires CE Kit 30679. For additional details, see the separate product specific Declaration of Conformity (DOC) sheet. Model No. Serial No.
Safety • Keep all parts in good working condition and all This machine has been designed in accordance with ANSI B71.4-2017 and EN ISO 5395. • Use only accessories, attachments, and hardware tightened. Replace all worn or damaged decals. replacement parts approved by Toro. General Safety This product is capable of amputating hands and feet and of throwing objects.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal93-6687 93-6687 1. Do not step here. decal93-7818 93-7818 1. Warning—read the Operator's Manual for instructions on torquing the blade bolt/nut to 115-149 N-m (85-110 ft-lb). decal93-6696 93–6696 1. Stored energy hazard—read the Operator's Manual. decal107-2908 107-2908 1.
decal133-8061 133-8061 decal112-1461 112-1461 1. Belt routing decal117-4979 117–4979 1. Entanglement hazard, belt—stay away from moving parts, keep all guards and shields in place. decal120-6604 120-6604 1. Thrown object hazard—keep bystanders away from the machine. 2. Cutting/dismemberment hazard of hand, mower blade—stay away from moving parts, keep all guards and shields in place. 3.
Setup (Figure 4) is reduced, making it much easier to disconnect the pull links from the machine. Note: Determine the left and right sides of the machine from the normal operating position. Installing the Pedal Spacer For 60-inch and 62-inch Mower Decks on Groundsmaster 360 Machines Note: This procedure is only for 60 and 62-inch mower decks installed on Groundsmaster 360 machines. 1. Remove the existing spacer from the machine as shown in Figure 3. 2.
g012230 Figure 6 1. Drive shaft 3. Roll pin 2. Capscrews and locknuts 4. Gearbox g017278 Figure 5 1. HOC pin 4. Loosen the 2 capscrews and locknuts (Figure 6). C. Slide the drive shaft end yoke from the gearbox shaft. 2. HOC bracket Start the engine, lower the cutting unit to the ground, shut off the engine, and remove the key. Note: Raise and tie the drive shaft to the frame. Note: Lowering the cutting unit onto furniture dollies aids in removing the cutting unit.
4. Start the engine and fully raise the cutting unit. Shut off the engine and remove the key from the ignition switch. Note: Place a wood block or similar shim under each link to hold it in the raised position. CAUTION The pull link torsion springs may cause some rotation of the pull links during installation. Use caution when connecting the pull links to the machine. 5. Align the pull link to the carrier frame and attach the link with the retainer pin (Figure 4).
Operation located in the second row. This does not add 6 mm (1/4 inch) to the 15.8 cm (6 inch) position. 4. Note: Determine the left and right sides of the machine from the normal operating position. Adjusting the Skid(s) Adjustments Mount the skids in the lower position when operating in height of cuts higher than 64 mm (2-1/2 inches) and in the higher position when operating in height of cuts lower than 64 mm (2-1/2 inches). Adjusting the Height-of-Cut The height-of-cut is adjusted from 2.5 to 15.
Adjusting the Rear Anti-Scalp Rollers Whenever you change the height-of-cut, adjust the height of the rear anti-scalp rollers. 1. Disengage the PTO, release the traction pedal, and engage the parking brake. 2. Move the throttle lever to the SLOW position, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
g004487 Figure 12 All Cutting Units 1. Front roller 2. Roller shaft g004925 Figure 15 Side-discharge cutting units only 1. Bolt 2. Chute-side roller 3. Spacer 4. Nut 5. Bracket g004926 Figure 13 Guardian mowers only 1. Bolt 2. Rear under-cutting unit roller 3. Spacer 4. Nut 5. Bracket g004924 Figure 16 Side-discharge cutting units only 1. Bolt 3. Under-cutting unit roller (2) 2. Roller shaft 4. Bracket 5. g004923 Figure 14 Guardian mower only 1. Bolt 2. Front under-cutting unit roller 3.
Operating Tips inside the cutting unit, cutting quality will eventually become unsatisfactory. Fast Throttle Setting/Ground Speed To reduce the risk of fire hazard, keep the engine, muffler, battery compartment, parking brake, cutting units, and fuel storage compartment free of grass, leaves, or excessive grease. Clean up any spilled oil or fuel. To maintain enough power for the machine and deck while mowing, operate the engine at the fast throttle position and adjust your ground speed for conditions.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. WARNING If you raise the machine using only a jack to support it while you work under the cutting unit, the jack could tip, causing the mower deck to fall, crushing you or bystanders. Always secure the machine with at least 2 jack stands when you have the mower deck raised. CAUTION On the top of the cutting unit are 2 links that connect them to the frame.
Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 50 hours • Check the condition of the blade drive belts on the cutting unit. Before each use or daily Every 50 hours • Check the cutting unit blades. • Clean the cutting unit. • Grease the bearing and bushing grease fittings. Daily Maintenance Checklist Duplicate this page for routine use. Maintenance Check Item For the week of: Mon. Tues. Wed. Thurs. Fri. Sat. Sun.
Lubrication Dusty and dirty operating conditions could cause dirt to get into the bearings and bushings, resulting in accelerated wear. Lubricate the grease fittings immediately after every washing, regardless of interval specified. Greasing the Bearings and Bushings Service Interval: Every 50 hours The machine has grease fittings that must be lubricated regularly with No. 2 lithium grease. Bearings and bushings must be lubricated daily when operating conditions are extremely dusty and dirty. 1.
g004646 Figure 19 Note: Bearing life can be negatively affected by improper wash down procedures. Do not wash the unit when it is still hot and avoid directing high-pressure or high volume spray at the bearings or seals.
Replacing the Blade Drive Belts turns grass brown at the edges, which slows growth and increases the chance of disease. Check the blades daily for sharpness, and for any wear or damage. Sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade. Service Interval: After the first 50 hours The blade drive belts, tensioned by the spring loaded idler pulleys, are very durable. However, after many hours of use, the belts will show signs of wear.
g004633 Figure 22 1. Measure here from blade to hard surface g004653 3. Wear/slot forming 2. Sail area 4. Crack Disengage the PTO, release the traction pedal, and engage the parking brake. 2. Move the throttle lever to the SLOW position, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Rotate the opposite ends of the blades forward. 5.
1. Disengage the PTO, release the traction pedal, and engage the parking brake. 2. Move the throttle lever to the SLOW position, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Hold the blade end using a rag or thickly-padded glove. 4. Remove the blade bolt, anti-scalp plate, and blade from the spindle shaft; refer to Figure 25 in Installing the Blades (page 19). Installing the Blades 1.
5. Remove the covers from the top of the cutting units. 6. Rotate the blade on each spindle until the ends face forward and backward. 7. Measure from the floor to the front tip of the cutting edge. 8. Adjust the jam nuts securing the cutting unit yokes/chains to the mower until the cutting unit is level (Figure 26). Replacing the Grass Deflector WARNING An uncovered discharge opening allows the machine to throw objects toward you or bystanders, which can result in serious injury.
Storage up to test that it lowers into the full down position. Cleaning Under the Cutting Unit 1. Disengage the PTO, release the traction pedal to the neutral position, and engage the parking brake. 2. Move the throttle lever to the SLOW position, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operator’s position. 3. Allow the engine to cool before adjusting, cleaning, storing, or repairing the machine. 4.
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. Serial No.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Conditions and Products Covered Parts The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
