Installation Instructions

ManualsBrandsToro ManualsAttachmentsRear Quick Attach System, Groundsmaster 7200 Series Mower

FormNo.3364-982RevA

RearQuickAttachSystem

Groundsmaster7200SeriesMower

ModelNo.30377—SerialNo.310000001andUp

InstallationInstructions

Installation

Important:Themachinemustbeequippedwith

theAuxiliaryPowerUnitKit,ModelNo.30382.

Note:Togainadditionalaccessduringtheassemblyof

thekit,raisetherearofthetractionunit,supportitwith

jackstandsandremovetherightreartire.

1.Mounttherearliftarmtotherearframemembers,

with2screws(7/8x4-1/2inch),lockwashers

(7/8inch)andlocknuts(7/8inch).Positionthe

componentsasshownin

Figure1.Useasmany

washersaspossibletoevenlyshimbetweentheright

andleftsidesoftheliftarmandrearframemembers.

Torquethescrewsandlocknutsto382-478ft-lb.

Figure1

1.Rearliftarm3.Washer(asrequired)

2.Greasetting

2.Threadthegreasettingintotherearoftheliftarm

(

Figure1).

3.Threada45degreehydraulicttingintoeachport

ofthehydrauliccylinder(Figure2).Makesurethe

O-ringsareinplacewheninstallingthettings.

OrientatethettingsasshowninFigure3.

Figure2

1.Hydrauliccylinder

3.Hydraulichose(16.5inch

long)

2.45degreehydraulictting

(2)

4.Hydraulichose

Figure3

1.90degrees

4.Installthestraightttingendofeachhydraulichose

tothettingsonthehydrauliccylinder(

Figure2).

Theshorterhose(16.5incheslong)isconnectedto

thettingclosesttotherodend.

5.Mounttherodendofthehydrauliccylindertothe

liftarmwithapivotpin(Figure4).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (16 pages)

PAGE 1
Form No. 3364-982 Rev A Rear Quick Attach System Groundsmaster 7200 Series Mower Model No. 30377—Serial No. 310000001 and Up Installation Instructions Installation Important: The machine must be equipped with the Auxiliary Power Unit Kit, Model No. 30382. Note: To gain additional access during the assembly of the kit, raise the rear of the traction unit, support it with jack stands and remove the right rear tire. 1.
PAGE 2
Figure 4 1. Hydraulic cylinder rod end 2. Lift arm 3. Pivot pin 4. Grease fitting 6. Secure the pivot pin to the lift arm with a screw (3/8 x 1-1/4 inch) and a flange nut (3/8), positioning as shown in Figure 4. Figure 6 1. Hydraulic manifold 7. Thread a 90 degree grease fitting into the end of the pivot pin (Figure 4). Position the grease fitting as shown in Figure 5. 2. Lift adapter 9. Mount the lift adapter to the rear lift arm with a pivot pin (Figure 7).
PAGE 3
Figure 11 1. Lift adapter 2. Threaded link 3. Link mount 14. Raise the lift adapter and secure the other rod end to the link mount with a 1/2 x 1-1/2 inch bolt and 1/2 inch nut (Figure 11). Figure 8 15. Mount the stationary end of the hydraulic cylinder to the underside of the frame cross member bracket with a pivot pin (Figure 12). 1. Lift mount 11. Assemble the rod ends and jam nuts to the hex tube to form the threaded link (Figure 9). The nuts and the rod ends have right and left hand threads.
PAGE 4
Figure 13 1. Pivot pin 2. Grease fitting 3. 45 degrees (2) Important: Make sure the O-rings are coated with fresh clean oil and in place when installing the fittings and hoses. 18. Connect the 2 hoses from the hydraulic cylinder to the fittings on the bottom of the hydraulic manifold (Figure 14 thru Figure 16). Orientate the fitting as shown in Figure 15. Figure 15 1. 30 degrees (2) 2. 30 degrees (2) 19. Thread the 45 degree hydraulic fittings into the bottom of the hydraulic manifold (Figure 14).
PAGE 5
Figure 16 Summer application shown 1. Protective sleeve 2. Cable tie 23. On the right side of the machine, just ahead of the radiator frame, place a drain pan under the oil cooler return hose (lower hose) (Figure 17). Figure 18 1. Short hose 2. Tee fitting 26. Measure approximately 5 inches from the radiator frame and cut the oil cooler return hose. This is the hose between the deck lift valve and the oil cooler. Hold the hose ends upward to decrease the amount of hydraulic fluid lost (Figure 19). 27.
PAGE 6
Figure 21 1. Power beyond sleeve fitting 2. 90 degree fitting 32. Thread a 90 degree fitting into the sleeve fitting on the valve and position as shown in Figure 21. 33. Route the long manifold hose forward, under the radiator frame, over the frame cross member and along the frame rail back to the valve (Figure 16) Figure 19 1. Cut hose here 2. Tee fitting 3. To deck lift valve 4. From oil cooler 34. Secure the hose fitting to the valve fitting (Figure 16).
PAGE 7
Figure 23 1. Power beyond sleeve fitting Figure 25 2. 45 degree fitting 1. Control panel 39. Thread a 45 degree fitting into the sleeve fitting on the valve (Figure 23). 40. Route the long manifold hose forward, under the radiator frame, over the frame cross member and thru the hole in the bulk head (Figure 22) to the front of the machine. Stay clear of hot or rotating components. 41. Secure the hose fitting to the valve fitting. 2. Latch 44.
PAGE 8
• To main harness connector located under the right operators controls by the SCM Note: The main harness connector is a 2 wire Metri-pak connector (brown and tan wires) • Pink power wire connector • Ground to ground block • Lift/Lower switch • Float/Enable switch Figure 27 1. Decal 3. Lift/Lower (3 position switch) 49. Secure the wire harness with cable ties. Important: Keep the harness away from all hot, sharp or moving parts. 2. Float/Power down (2 Position switch) 50.
PAGE 9
Operation Lift/Lower Switch Move switch to Lift to raise attachment and to Lower to lower attachment (Figure 29). Float/Power Down Switch Figure 30 1. Threaded link Moving the switch to Float allows the attachment to follow the contour of the ground. Moving the switch to Power Down will add weight from the machine to increase ground engagement force (Figure 29). Higher ground engagement force will decrease the traction capacity of the machine. Figure 29 1. Float/Power Down switch 2.
PAGE 10
Weight Charts Use the following weight charts to determine the correct amount of front weight required for your machine.
PAGE 11
62 inch width of cut Models 30362 and 30365 With NO hard canopy, model 30359 AND Additional Front Weight Required Weight Part Number Weight Description Qty.
PAGE 12
Maintenance Operating Tips • Read and understand the attachment Operator’s manual prior to use. • Lubricate the (5) grease fittings with No. 2 Lithium based grease weekly or after every washing. • Make sure the appropriate weight mount bracket and front weight(s) are installed for the rear attachment. • When operating in dusty conditions the air cleaner should be checked daily. A safety air cleaner element is available and may be added to the existing air cleaner for additional engine protection.
PAGE 13
Notes: 13
PAGE 14
Notes: 14
PAGE 15
Notes: 15
PAGE 16
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).