Installation Instructions

ManualsBrandsToro ManualsAttachmentsAuxiliary Power Unit, Groundsmaster 3320/3280-D and 7200/7210 Traction Units

FormNo.3406-911RevA

AuxiliaryPowerUnit

Groundsmaster

3320/3280-Dand7200/7210TractionUnits

ModelNo.30382

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Powerrelay1

Locknut

Screw

Fuseblock1

Groundblockterminal

Jumperstrip1

Powerpoint1

Cap

Installthepowerunit.

Wireharness(3connections)

Wireharness(7connections)

Fuse(10A)

Routethewireharness.

PreparingtheMachine

NoPartsRequired

Procedure

1.Movethemachinetoalevelsurface(boxAofFigure1).

2.Engagetheparkingbrake(boxBofFigure1).

3.Removethekeyfromtheignitionswitch(boxCofFigure1).

4.Removethenegativebatterycablefromthebattery(boxDofFigure1).

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3406-911*A

Summary of content (8 pages)

PAGE 1
Form No. 3406-911 Rev A Auxiliary Power Unit Groundsmaster® 3320/3280-D and 7200/7210 Traction Units Model No. 30382 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Qty. No parts required – Power relay Locknut Screw Fuse block Ground block terminal Jumper strip Power point Cap Wire harness (3 connections) Wire harness (7 connections) Fuse (10 A) 1 5 5 1 1 1 1 1 1 1 1 Use Prepare the machine.
PAGE 2
. Mount the ground terminal block to the bottom of the compartment with 2 screws and 2 locknuts (Figure 3). 2 Note: Do not use the locknuts if flat nuts exist on the bracket. Installing the Power Unit Parts needed for this procedure: 1 Power relay 5 Locknut 5 Screw 1 Fuse block 1 Ground block terminal 1 Jumper strip 1 Power point 1 Cap For a Groundsmaster 3320/3280-D Machine Figure 3 1. Screw 2. Ground terminal block 1.
PAGE 3
For a Groundsmaster 7200/7210 Machine 5. Mount the power relay to the flat nut on the side of the compartment with a screw (Figure 5). Note: Use a locknut if there is no flat nut. You may need to remove the 4 screws securing the mounting panel and pull up the mounting panel to install the locknut. 1. Unlatch and raise the seat. 2. Unlatch the control-panel assembly and lay it aside (Figure 7). G018078 Figure 7 1. Control-panel assembly 3.
PAGE 4
Note: Install the screws from the underside of the panel as shown in Figure 9. Figure 11 1. Power point in knockout location 8. Unscrew the outer shell from the threaded power point connector body. Figure 9 1. Locknut 2. Fuse block 2. Cap 3. Screw 9. From the seat side of the control panel, insert the power point into the hole, secure it with the outer shell, and insert the cap into the power point. 6. Mount the power relay to the inside of the control panel with a screw and nut (Figure 10).
PAGE 5
3 Routing the Wire Harness Parts needed for this procedure: 1 Wire harness (3 connections) 1 Wire harness (7 connections) 1 Fuse (10 A) G018074 Figure 12 1. Accessory relay connector For a Groundsmaster 3320/3280-D Machine (Serial Numbers 250000001 through 259999999) 3. Black wire 2. Large, red wire 2. Connect the large, red wire (Figure 12) from the auxiliary fuse block to the mating connector from the traction-unit harness. Note: Use the wire harness with 3 connections. 1.
PAGE 6
For a Groundsmaster 3320/3280-D (Serial Numbers 260000001 and up) or Groundsmaster 7200/7210 Machine Note: Make sure that the fuses are installed in the slots that have wires connected to the harness. The remaining fuse block wires are not used at this time. 5. Connect the large, red wire from the fuse block to the mating connector from the wire harness. Note: Use the wire harness with 7 connections. Refer to Figure 14 for the procedure. 6. Plug the wire harness connector into the power relay connector.
PAGE 7
Notes:
PAGE 8