Installation Instructions

ManualsBrandsToro ManualsRiding ProductsService Cutting Unit, Groundsmaster 4100-D Models 30447 and 30449

Table Of Contents

FormNo.3395-707RevA

ServiceCuttingUnit

ModelNo.30451—SerialNo.315000001andUp

InstallationInstructions

Installation

Note:IftheservicecuttingunitistobeusedonaModel

30411or30413TractionUnit,theDeckSensorKit,PartNo.

119-5307mustalsobeinstalledonthecuttingunit.

1.Parkthemachineonalevelsurface,lowerthecutting

unittotheoor,engagetheparkingbrake,setthe

tractionpedalisintheNEUTRALpositionandthePTO

isOFF.ShuttheengineOFFandremovethekeyfrom

theswitch.

2.Removetheboltssecuringthehydraulicmotorstothe

deck(Figure1).

Figure1

1.Hydraulicmotor2.Mountingbolts

3.Liftthemotorsoffthedeckandlaythemonaclean,

outoftheway,surface.

Note:Donotdamagealuminiumcouplers.

4.Removetheelastomericspiderfrominsideeachpulley

coupler.Inspecttheelastomericspiderforwearand

replaceitifworn.Otherwise,retainforinstallingon

thenewdeck(Figure2).

Figure2

1.Spider

3.Pulleycoupler

2.Spiderhub

Note:Inspectspiderhubforwearandreplaceifitis

worn(Figure2).

5.Disconnectthehydraulichosesfromthewing-deck-lift

cylinders(Figure3).

Important:Whenassemblingthehydraulichoses

totheliftcylinders,makesurethattheO–rings

areinplaceandthatthettingsaretorquedto17

to19ft–lb.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3395-707*A

Summary of content (4 pages)

PAGE 1
Form No. 3395-707 Rev A Service Cutting Unit Model No. 30451—Serial No. 315000001 and Up Installation Instructions Installation Note: If the service cutting unit is to be used on a Model 30411 or 30413 Traction Unit, the Deck Sensor Kit, Part No. 119-5307 must also be installed on the cutting unit. 1. Park the machine on a level surface, lower the cutting unit to the floor, engage the parking brake, set the traction pedal is in the NEUTRAL position and the PTO is OFF.
PAGE 2
Figure 5 1. Damper 2. Hairpin cotter Figure 3 1. Wing-deck-lift cylinder 2. Hydraulic hoses 9. Remove the bolts, spacers, and flange nuts securing the other end of the dampers to the cutting unit (Figure 6). 6. Locate and unplug the cutting-unit wiring harness from the traction unit wiring harness (Figure 4). Note: Make sure that the spacer is positioned in front of the damper rod end when assembling to the cutting unit. Figure 6 Figure 4 1. Wiring harness 1. Damper 2. Cable tie 7.
PAGE 3
Figure 7 1. Height-of-cut chain 2. Clevis pin and hairpin cotter 11. Remove the bolts, washers, and locknuts securing each lift arm mount to the cutting-unit castor-arm tubes (Figure 8). Important: When re–assembling the lift arm mounts to the castor arm tubes, make sure they are positioned so the slotted mounting holes are to the rear and the fasteners are torqued to 75 to 85 ft–lb. Figure 8 1. Lift-arm mount (2) 12. Move the cutting unit away from the traction unit. 13.
PAGE 4
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).