Installation Instructions

ManualsBrandsToro ManualsRiding ProductsService Cutting Unit, Groundsmaster 4100-D Models 30447 and 30449

FormNo.3362-820RevA

ServiceCuttingUnit

Groundsmaster4100-DModels30447and30449

ModelNo.30451—SerialNo.310000001andUp

InstallationInstructions

Installation

Note:Iftheservicecuttingunitistobeusedona

Model30411or30413TractionUnit,theDeckSensor

Kit,PartNo.119-5307mustalsobeinstalledonthe

cuttingunit.

1.Parkthemachineonalevelsurface,lowerthecutting

unittotheoor,engagetheparkingbrake,besure

thetractionpedalisintheneutralpositionandthe

PTOisOFF .ShuttheengineOFFandremovethe

keyfromtheswitch

2.Removetheboltssecuringthehydraulicmotorsto

thedeck(

Figure1).Liftthemotorsoffthedeckand

laythemonaclean,outoftheway,surface.Donot

damagealuminiumcouplers.

Figure1

1.Hydraulicmotor2.Mountingbolts

3.Removetheelastomericspiderfrominsideeach

pulleycoupler.Inspectforwearandreplaceifworn.

Otherwise,retainforre–installationonnewdeck

(

Figure2).

Figure2

1.Spider

3.Pulleycoupler

2.Spiderhub

Note:Inspectspiderhubforwearandreplaceif

worn(Figure2).

4.Disconnectthehydraulichosesfromthewingdeck

liftcylinders(

Figure3).

Important:Whenre–assemblingthehydraulic

hosestotheliftcylinders,makesuretheO–rings

areinplaceandthettingsaretorquedto17to

19ft–lbs.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3362-820 Rev A Service Cutting Unit Groundsmaster 4100-D Models 30447 and 30449 Model No. 30451—Serial No. 310000001 and Up Installation Instructions Installation Note: If the service cutting unit is to be used on a Model 30411 or 30413 Traction Unit, the Deck Sensor Kit, Part No. 119-5307 must also be installed on the cutting unit. 1.
PAGE 2
Figure 5 1. Damper 2. Hair pin cotter Figure 3 1. Wing deck lift cylinder 2. Hydraulic hoses 7. Remove the bolts, spacers and flange nuts securing the other end of the dampers to the cutting unit (Figure 6). 5. Locate and unplug the cutting unit wire harness from the traction unit wire harness (Figure 4). Also, remove any cable ties securing the cutting unit wire harness to any traction unit components.
PAGE 3
Figure 7 1. Height of cut chain 2. Clevis pin and hairpin cotter 9. Remove the bolts, washers and locknuts securing each lift arm mount to the cutting unit castor arm tubes (Figure 8). Important: When re–assembling the lift arm mounts to the castor arm tubes, make sure they are positioned so the slotted mounting holes are to the rear and the fasteners are torqued to 75–85 ft–lbs. Figure 8 1. Lift arm mount (2) 10. Move the cutting unit away from the traction unit. 11.
PAGE 4
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).