Form No. 3389-362 Rev A 60in, 62in, and 72in Rotary Mowers Groundsmaster® 360 Series and 7200 Series Traction Unit Model No. Model No. Model No. Model No. Model No. Register at www.Toro.com. Original Instructions (EN) 30353—Serial No. 30354—Serial No. 30456—Serial No. 30457—Serial No. 30481—Serial No.
Mowers with model numbers 30353, 30457 and 30354 comply with all relevant European directives, for details please see the separate product specific Declaration of Conformity (DOC) sheet. Figure 1 1. Safety alert symbol Mower model number 30456 complies with all relevant European directives, when the CE Kit, Part No. 117-9248 is installed on the mower. Mower model number 30353 requires CE kit 30685, 30457 requires CE kit 30683, 30354 requires CE kit 30679, 30456 requires CE kit 30658.
Safe Handling of Fuels Safety • To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Safe Operating Practices The following instructions are adapted from the CEN standard EN ISO 5395:2013 and ANSI B71.4-2012. • Extinguish all cigarettes, cigars, pipes, and other sources This product is capable of amputating hands and feet and throwing objects.
Toro Riding Mower Safety • Do not change the engine governor settings or overspeed • • • • • • the engine. Operating the engine at excessive speed may increase the hazard of personal injury. Before leaving the operator's position: – disengage the power take-off and lower the attachments; – set the parking brake; – stop the engine and remove the key.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-6697 1. Read the Operator's Manual. 2. Add SAE 80w-90 (API GL-5) oil every 50 hours. 112-1461 1. Belt routing 93–6696 1. Stored energy hazard—read the Operator's Manual. 107-2908 1. Thrown object hazard—keep bystanders a safe distance from the machine. 2.
120-6604 1. Thrown object hazard—keep bystanders away from the machine. 2. Cutting/dismemberment hazard of hand, mower blade—stay away from moving parts, keep all guards and shields in place. 3. Cutting/dismemberment hazard of foot, mower blade—stay away from moving parts, keep all guards and shields in place.
Setup Media and Additional Parts Description Use Qty. Parts catalog Operator's Manual 1 1 Review the material and save in an appropriate place: Note: Determine the left and right sides of the machine from the normal operating position. A. Remove the shoulder screw that secures the retainer pin to the carrier frame (Figure 2). B. Removing the Existing Mower (if applicable) Carefully slide the retainer pin from the carrier frame and the pull link (Figure 2). 3.
A. Remove the roll pin from the end yoke and the gearbox shaft (Figure 4). CAUTION Be careful when connecting the pull links to the machine. The pull link torsion springs may cause some rotation of the pull links during installation. 5. Align the pull link to the carrier frame and attach the link with the retainer pin (Figure 2). Secure the retainer pin to the frame with the shoulder screw (Figure 2). 6. Install the HOC pin into the HOC bracket at the desired height of cut (Figure 3). 7.
Operation Note: Determine the left and right sides of the machine from the normal operating position. Adjustments Adjusting the Height-of-Cut The height-of-cut is adjusted from 2.5 to 15.8 cm (1 to 6 inches) in 6 mm (1/4 inch) increments by relocating the stop pin into different hole locations. 1. With the engine running, push back on the mower lift switch until the mower is fully raised and release the switch immediately (Figure 6). Figure 5 1. Chain 2. Yoke 3. Jam nut 4.
Adjusting the Skid(s) 3. After adjusting the height-of-cut, adjust the rollers by removing the flange nut, bushing, spacer, and bolt (Figure 8). Mount the skids in the lower position when operating in height of cuts higher than 64 mm (2-1/2 inches) and in the higher position when operating in height of cuts lower than 64 mm (2-1/2 inches). Note: On Guardian® mowers, when the skids become worn, you can switch the skid to the opposite sides of the mower, flipping them over.
2. Move the throttle lever to the Slow position, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Raise the front of the machine and support it on jack stands. 4. Remove the fasteners securing each roller on your mower and move the rollers up or down as desired; refer to Figure 10 through Figure 14 as applicable for your mower. Figure 12 Guardian Mower Only 1. Bolt 2. Front under-mower roller 3. Nut 4. Bracket Figure 10 All Mowers 1.
dense grass, you may have to slow down the forward speed and/or raise the height-of-cut to the next higher setting. Important: If cutting more than 1/3 of the grass blade off, or in sparse long grass or dry conditions, the use of flat sail blades is recommended to reduce air-borne chaff, debris, and deck drive component strain.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. WARNING If you raise the machine using only a jack to support it while you work under the mower deck, the jack could tip, causing the mower deck to fall, crushing you or bystanders. Always secure the machine with at least 2 jack stands when you have the mower deck raised. CAUTION On the top of the mower deck are two links that connect them to the frame.
Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 50 hours • Check the condition of the blade drive belts on the mower. Before each use or daily Every 50 hours • Check the mower blades. • Clean the mower. • Grease the bearing and bushing grease fittings. Daily Maintenance Checklist Duplicate this page for routine use. Maintenance Check Item For the week of: Mon. Tues. Wed. Thurs. Fri. Sat. Sun.
Lubrication operating conditions are extremely dusty and dirty. Dusty and dirty operating conditions could cause dirt to get into the bearings and bushings, resulting in accelerated wear. Lubricate the grease fittings immediately after every washing, regardless of interval specified. Greasing the Bearings and Bushings Service Interval: Every 50 hours 1. Wipe the grease fittings clean so foreign matter cannot be forced into the bearing or bushing.
Figure 17 Note: Bearing life can be negatively affected by improper wash down procedures. Do not wash down the unit when it is still hot and avoid directing high-pressure or high volume spray at the bearings or seals.
Replacing the Blade Drive Belts DANGER A worn or damaged blade can break, and a piece of the blade could be thrown into the operator's or bystander's area, resulting in serious personal injury or death. Service Interval: After the first 50 hours The blade drive belts, tensioned by the spring loaded idler pulleys, are very durable. However, after many hours of use, the belts will show signs of wear.
Figure 20 1. Measure here from blade to hard surface 2. Position A 4. Rotate the opposite ends of the blades forward. 5. Measure from a level surface to the cutting edge of the blades at the same position as in step 3 above. The difference between the dimensions obtained in steps 3 and 4 must not exceed 3 mm (1/8 inch). If this dimension exceeds 3 mm (1/8 inch), the blade is bent and must be replaced; refer to Removing the Blades and Installing the Blades. WARNING Figure 19 1. Cutting Edge 3.
2. Remove the blade bolt, anti-scalp plate, and blade from the spindle shaft (Figure 23). Sharpening the Blades WARNING When sharpening blade, pieces of blade could be thrown and cause serious injury. Wear proper eye protection when sharpening blades. 1. Sharpen the cutting edge at both ends of the blade (Figure 21). Maintain the original angle. The blade retains its balance if the same amount of material is removed from both cutting edges. Figure 21 Figure 23 1. Sharpen at original angle 2.
Replacing the Grass Deflector WARNING An uncovered discharge opening could allow the machine to throw objects in the operator's or bystander's direction and result in serious injury. Also, contact with the blade could occur. • Never operate the machine without a mulch kit or grass deflector installed. • Make sure the grass deflector is in the down position. 1.
Cleaning Under the Mower Storage Service Interval: Before each use or daily 1. Thoroughly clean the mower, paying special attention to these areas: Remove the grass buildup under the mower daily. 1. Disengage the PTO, release the traction pedal to the neutral position and set the parking brake. • Underneath the mower 2. Move the throttle lever to the Slow position, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
Notes: 22
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. Serial No.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
