Installation Instructions

ManualsBrandsToro ManualsRiding ProductsRear Discharge Completion Kit, Groundsmaster 7200 Series Traction Unit with 62in Mower

Printed in the USA

W 2007, Rev 2008 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Rear Discharge Completion Kit

Groundsmaster

)

7200 Series Traction Unit with 62 in.

Mower

Groundsmaster

)

7200 Series Traction Unit with 72 in.

Mower

Model No. 30463

Model No. 30466

Form No. 3358–528 Rev. C

Installation Instructions

62” Rear Discharge Completion Kit, Model 30463 can be

installed on the following Groundsmaster 7200 Series

Traction Units with 62 in. Mowers:

30365

30362

30462

30465

72” Rear Discharge Completion Kit, Model 30466 can be

installed on the following Groundsmaster 7200 Series

Traction Units with 72 in. Mowers:

30361

30364

30364TC

30461

30464

30464TC

Remove the Existing Recycling

Baffles from the Cutting Unit

Note: This procedure is not required on models shipped

without the cutting unit baffles installed.

1. Disengage the PTO, move the motion control levers to

the neutral locked position and set the parking brake.

2. Move the throttle lever to the Slow position, stop the

engine, remove the key, and wait for all moving parts

to stop before leaving the operating position.

Danger

If you raise the machine using only a jack to

support it while you work under the mower deck,

the jack could tip, causing the mower deck to fall,

crushing you or bystanders.

• Always secure the machine with at least 2 jack

stands when you have the mower deck raised.

3. Remove the flange nut, screw and spacer securing the

deck roller to the mounting bracket (Fig. 1). Remove

components.

4. Remove the carriage bolts and nuts securing the roller

mounting bracket to the underside of the mower deck

(Fig. 1). Remove the mounting bracket.

5. Remove the carriage bolts and flange nuts securing the

center, left and right baffles to the underside of the

mower deck (Fig. 1). Remove the baffles from the

mower deck.

62” Mower shown

Figure 1

1. Deck roller

2. Roller mounting bracket

3. Baffle

Summary of content (8 pages)

PAGE 1
Rear Discharge Completion Kit Form No. 3358–528 Rev. C Groundsmaster) 7200 Series Traction Unit with 62 in. Mower Groundsmaster) 7200 Series Traction Unit with 72 in. Mower Model No. 30463 Model No. 30466 Installation Instructions 62” Rear Discharge Completion Kit, Model 30463 can be installed on the following Groundsmaster 7200 Series Traction Units with 62 in. Mowers: 3. Remove the flange nut, screw and spacer securing the deck roller to the mounting bracket (Fig. 1). Remove components.
PAGE 2
62 Inch Rear Discharge Completion Kit Installation 3. Mount the support straps and deflector to the rear angle with (8) 5/16 x 7/8 in. carriage bolts and flange nuts (Fig. 2). The bolt heads are to be positioned next to the rear angle. 1. Loosely mount the new chambers to the under side of the mower deck with (12) 5/16 x 3/4 in. carriage bolts and flange nuts (4 bolts & nuts per chamber). The bolt heads are to positioned inside the mower deck. Position the chambers as shown in figure 2. 4.
PAGE 3
7. Install the blades, anti-scalp cups, and blade bolts (Fig. 3). Tighten the blade bolts to 85–110 ft.-lb. (115–149 N⋅m). 10. Affix an identification decal to the top of the mower deck near the serial plate (Fig. 4). Make sure the mounting surface is clean. Important The curved part of the blade must be pointing toward the inside of the cutting unit to ensure proper cutting. Affix this identification decal, part no. 115–1408 onto 62 inch mower decks. 3 2 1 1 Figure 3 1. Blade bolt 2.
PAGE 4
72 Inch Rear Discharge Completion Kit Installation 4. Loosely mount the rear angle w/deflector to the rear of the mower deck with (4) 5/16 x 7/8 in. carriage bolts and flange nuts (Fig. 5). The bolt heads are to be positioned next to the rear angle. 1. Loosely mount the new chambers to the under side of the mower deck with (12) 5/16 x 3/4 in. carriage bolts and flange nuts (4 bolts & nuts per chamber). The bolt heads are to positioned inside the mower deck. Position the chambers as shown in figure 5. 5.
PAGE 5
9. Install the blades, anti-scalp cups, and blade bolts (Fig. 3). Tighten the blade bolts to 85–110 ft.-lb. (115–149 N⋅m). 11. Affix an identification decal to the top of the mower deck near the serial plate (Fig. 4). Make sure the mounting surface is clean. Important The curved part of the blade must be pointing toward the inside of the cutting unit to ensure proper cutting. Affix this identification decal, part no. 115–1409 onto 72 inch mower decks 3 2 1 1 Figure 6 1. Blade bolt 2.
PAGE 6
PAGE 7
PAGE 8