Installation Instructions

ManualsBrandsToro ManualsRiding ProductsFender and Rear Discharge Completion Kit, Groundsmaster 7200 Series Traction Unit with 72in Mower

FormNo.3395-963RevA

FenderandRearDischargeCompletionKit

Groundsmaster

7200SeriesTractionUnitwith62inMower

ModelNo.30469

ModelNo.30472

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

The62-inchRearDischargeCompletionKit(Model30469)

canbeinstalledonthefollowingGroundsmaster7200Series

TractionUnitswith62-inchMowers:

•30365

•30362

•30462

•30465

•30465N

•30495(with30457)

•30487(with30457)

•30695(with30457)

The72-inchRearDischargeCompletionKit(Model30472)

canbeinstalledonthefollowingGroundsmaster7200Series

TractionUnitswith72-inchMowers:

•30361

•30364

•30364TC

•30461

•30464

•30464TC

•30464N

•30495(with30353)

•30487(with30353)

•30695(with30353)

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Removetheexistingrecyclingbafefromthecuttingunit.

Nut(5/16inch)

Carriagebolt(5/16x3/4inch)

Carriagebolt(5/16x7/8inch)

Leftfootshield

Rightfootshield

Deector

Rearangle2

Supportstrap

Leftchamber

Centerchamber

Rightchamber1

Blade3

Anti-scalpcup3

Bladebolt3

Identicationdecal

Installthereardischargecompletionkit(for62-inchdecks).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3395-963*A

Summary of content (12 pages)

PAGE 1
Form No. 3395-963 Rev A Fender and Rear Discharge Completion Kit Groundsmaster® 7200 Series Traction Unit with 62in Mower Model No. 30469 Model No. 30472 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
Description Nut (5/16 inch) Carriage bolt (5/16 x 3/4 inch) Carriage bolt (5/16 x 7/8 inch) Left foot shield Right foot shield Deflector Rear angle Support strap Left chamber Center chamber Right chamber Left deflector Washer Bolt (5/16 x 3/4 inch) Blade Anti-scalp cup Blade bolt ID decal Fender mount Right fender Thread-forming screw (5/16 x 5/8 inch) Bolt (1/4 x 5/8 inch) Nut (1/4 inch) Left fender Nut (3/8 inch) Bolt (3/8 x 3/4 inch) Use Qty.
PAGE 3
Removing the Existing Recycling Baffles from the Cutting Unit DANGER If you raise the machine using only a jack to support it while you work under the mower deck, the jack could tip, causing the mower deck to fall, crushing you or bystanders. Always secure the machine with at least 2 jack stands when you have the mower deck raised. Note: This procedure is not required on models shipped without the cutting unit baffles installed. 1.
PAGE 4
Installing the Rear Discharge Completion Kit 62-Inch Decks Only 1. Loosely mount the new chambers to the underside of the mower deck with 12 carriage bolts (5/16 x 3/4 inch) and 12 nuts (5/16 inch). Note: Each chamber should have 4 sets of nuts and bolts. Position the bolt heads inside the mower deck. Position the chambers as shown in Figure 2. Figure 3 Note: If a required mounting hole is not present in the mower deck, use the new component as a template to locate, mark, and drill the holes (0.
PAGE 5
Figure 5 1. Left foot shield 2. Right foot shield 7. Mount the left foot shield to the top and side of the mower deck with 3 carriage bolts (5/16 x 3/4 inch) and 3 nuts (5/16 inch) as shown in Figure 5. Figure 7 1. Identification decal 8. Install the blades, anti-scalp cups, and blade bolts (Figure 6). Important: The curved part of the blade must point toward the top of the cutting unit to ensure proper cutting. Figure 6 1. Blade bolt 2. Anti-scalp cup 9.
PAGE 6
Installing the Rear Discharge Completion Kit (for 72-inch Decks) 72-Inch Decks Only 1. Loosely mount the new chambers to the underside of the mower deck with 12 carriage bolts (5/16 x 3/4 inch) carriage bolts and 12 nuts (5/16 inch). Note: Each chamber will have 4 sets of nuts and bolts. Position the bolt heads inside the mower deck. Position the chambers as shown in Figure 8.
PAGE 7
Figure 11 1. Support strap Figure 13 6. Tighten all fasteners. 7. Mount the right foot shield to the top and side of the mower deck with 4 carriage bolts (5/16 x 3/4 inch) carriage bolts and 4 nuts (5/16 inch) as shown in Figure 12. 1. Nut 2. Left foot shield 4. Washer 5. Capscrew 3. Deflector 6. Carriage bolt 9. Install the blades, anti-scalp cups, and blade bolts (Figure 14). Important: The curved part of the blade must point toward the top of the cutting unit to ensure proper cutting.
PAGE 8
Figure 17 1. Hose clamp 2. Bolt 5. Insert the bottom of the hose clamp through the slot in the top of the fender mount (Figure 18). Figure 15 1. Identification decal Installing the Right Fender 1. Position a suitable floor jack under the rear bumper tube and raise the rear tires off the ground (Figure 16). Note: Position the jack stands under the rear bumper. Figure 18 1. Fender mount 6. Loosely mount the hose clamp and fender mount to the frame channel with the bolt previously removed. 7.
PAGE 9
12. Using the newly drilled holes, secure the fender mount to the frame channel with 2 thread-forming screws (5/16 x 5/8 inch) as shown in Figure 21. 8. Use the frame mount as a template to locate and mark the other 2 fender mounting holes in the frame channel (Figure 19). Figure 19 1. Mark here. 9. Remove the bolt and nut securing the clamp and fender mount to the frame. Figure 21 1. Thread-forming screw (5/16 x 5/8 inch) 13. Tighten all the fasteners. 14.
PAGE 10
Installing the Left Fender 6. Loosely mount the bracket on the top of the left fender to the fuel-tank bracket with 2 bolts (3/8 x 3/4 inch) and 2 nuts (3/8 inch) as shown in Figure 24. 1. Disconnect the cable from the negative terminal of the battery. 2. Disconnect the cable from the positive terminal of the battery. 3. Remove the carriage bolt, washer, battery hold-down, and nut securing the battery (Figure 23). Note: Retain the hold-down and the fasteners. Figure 24 1. Fuel-tank bracket 2.
PAGE 11
13. Remove the jack stands and lower the machine. Note: Verify that the tires do not rub on the fenders when you drive the machine.
PAGE 12
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. Serial No.