Installation Instructions

ManualsBrandsToro ManualsAttachmentsCenter Mower Deck, Serial Number 313000001 and After Groundsmaster 4000-D Traction Unit

FormNo.3384-991RevA

CenterMowerDeck

SerialNumber313000001andAfterGroundsmaster

4000-D

TractionUnit

ModelNo.30479—SerialNo.400000000andUp

InstallationInstructions

RemovingtheHydraulic

Motor

1.Parkthemachineonalevelsurface,lowerthe

mowerdeck,engagetheparkingbrake,shutoff

theengine,andremovethekey.

2.EnsurethatthetractionpedalisintheNEUTRAL

positionandthePTOleverisintheOFFposition.

3.Removetheboltssecuringthehydraulicmotor

tothemowerdeck(Figure1).

4.Liftthemotoroffthemowerdeckandlayitona

clean,outoftheway,surface.

Note:Ensurethatyoudonotdamage

aluminumcoupler.

g011511

Figure1

1.Hydraulicmotor2.Mountingbolts

5.Removetheelastomericspiderfrominsidethe

pulleycoupler(Figure2).

6.Inspecttheelastomericspiderforwearand

replaceitifitisworn.Retainitforinstallationon

thenewfrontmowerdeck.

g011595

Figure2

1.Elastomericspider3.Pulleycoupler

2.Spiderhub

ReplacingtheFrontMower

Deck

WARNING

Theliftarmsraiseupwhenthemowerdeckis

removedandthemachineisturnedon.

Movethemowerdeckunderthemachineand

connectitbeforeturningthemachineon.

1.Removethehairpincottersandtheclevispins

securingtheheight-of-cutchainstotherearof

themowerdeck(Figure3).Retainthehardware

forinstallationonthenewmowerdeck.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3384-991*A

Summary of content (4 pages)

PAGE 1
Form No. 3384-991 Rev A Center Mower Deck Serial Number 313000001 and After Groundsmaster® 4000-D Traction Unit Model No. 30479—Serial No. 400000000 and Up Installation Instructions Removing the Hydraulic Motor 1. Park the machine on a level surface, lower the mower deck, engage the parking brake, shut off the engine, and remove the key. 2. Ensure that the traction pedal is in the NEUTRAL position and the PTO lever is in the OFF position. 3.
PAGE 2
g011596 Figure 3 1. Height-of-cut chain 2. 2. Clevis pin and hairpin cotter Remove bolts, washers, and locknuts securing each lift-arm mount to the caster-arm tube (Figure 4). g011597 Figure 4 1. Lift-arm mount (2) 3. Move the mower deck away from the traction unit. 4. Move the new mower deck into position and mount it to each caster-arm tube by reversing the procedure. 5. Adjust the height of cut for the mower deck; refer to the procedure in the Operator’s Manual for the machine.
PAGE 3
Notes:
PAGE 4
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).