FORM NO. 3314-130 MODEL NO: 30505 & UP INSTALLATION INSTRUCTIONS Toronto 15 CU. FT. HOPPER KIT GROUNDSMASTER® 220-D or 224 IMPORTANT: On Model 30784, GM 220-D or Model 30224, GM 224 traction units with serial numbers prior to 10001, the steering cylinder rod end must be checked to assure it has a grease groove. if rod end does not have a grease groove, a new rod end must be installed.
A SAFETY INSTRUCTIONS 13. Maximum seating capacity is one person. Therefore, never carry passengers. 14. Check carefully for overhead clearances before driving under any objects. 16. The grass deflector or complete blower assembly must always be installed on cutting unit, 18. To maintain machine control, 75 Ib. of weight must be mounted on left front wheel of traction unit before using the 15 cu. ft. Hopper kit. 17. Operator must be skilled and trained in how to drive on hillsides.
A SAFETY INSTRUCTIONS 84. Stay away from hopper and hopper linkage during operation. 35. Do not walk under hopper or service machine unless hopper is fully raised and empty, with hydraulic lines disconnected at quick couplets or fully dowered. 36. Do not remove any hydraulic line unless hopper is fully lowered or fully raised and empty. 37. f major repairs are ever needed or assistance is desired, contact an Authorized TOR Distributor. 38.
LOOSE PARTS Note: Use this chart as a checklist to ensure all parts necessary far assembly have been shipped. If any of these parts are missing, total set-up cannot be completed. DESCRIPTION QTy. USE Control Naive Assembly Control Valve Han die Control Valve Pivot Lever Roll Pin Clevis Pin Cotter Pin Tube Assembly Tube Assembly Cap screw Ig. Flange Lockout 1/4 -20 Clamp Cap screw 1/4 ~20 x ig.
SET-UP INSTRUCTIONS MOUNT CONTROL VALVE 1. Place a drain pan under fight naive (Fig. 1) on right side of machine. Figures 1 1. Lift Naive 2. Disconnect return line (Fig. 1}, from bottom of sift viva (line goes to radiator}. 3. Mount left control valve tube assembly to fitting on lift valve. 4. Mount right control valve tubes assembly 10 return line disconnected from lift valve. 5. l Loosely mount appropriate tube assemblies to fittings on girt and left sides of naive, positioning them as shown in figure 1.
SET-UP INSTRUCTIONS MOUNT HOPPER FRAME 1. Disconnect air cleanser hose from air cleaner body (Fig. 5}. 2. Loosen bands securing air cleaner body to mounting brackets (Fig. 5). 3. Remove (4) screws securing air cleanse mounting brackets to left side of frame (Fig. 5). Remove air cleaner brackets. Discard fasteners. Figure & 1. Alr Cleaner 2. Hose 3, Mounting Bracket 4.
SET-UP INSTRUCTIONS 10. Mount bottom of bracket 1o frame with 1g. cap screws, mounting strap, 172 Dishwashers and lockouts. Strap to be positioned between frame and washers. 11. From rear of machine, side front of hopper frame onto side mounting bracket pins and rear of frame over rear bracket pin. 12. Secure rear of frame to bracket pin with dis pin {Fig. 8. Conn SH Figure ¢ 1. Disconnect Pin 13, Inst alt short and long waded mounting pins through arm assembly and main Sift arm assembly.
SET-UP INSTRUCTIONS 3. Secure hopper to frame with (2) waled mounting pins and hair pin cottars (Fig.12}. 4. Secure hopper tig rods to frame with hair pin cotters (Fig. 13). Figure 13 1. Hopper Tie Rod &, Adjust tie rods up or down to make sure hopper is level with machine and it does not contact making during operation. INSTALL FRONT BLOWOUT SHIELDS Note: The following instructions are as viewed from the front of the machine. When hopper is used with a §2” Deck 1.
SET-UP INSTRUCTIONS Figure 16 1. Wheel Weight 2, Threaded Rod 5. Place wheel weight over ends of threaded rods and secure in place with Hat washers, lock washers and hex nuts (Fig. 16). Do not over tighten hex nuts or damage o the plastic housing of the wait may scour, Note: if thees is excess thread protruding from nuts or inside of wheal, cut it off with a hacksaw. Threaded rod must not contact any parts of the machine when wheel is rotating. BEFORE OPERATING HOPPER 1. Start engine.
OPERATING INSTRUCTIONS 6. The grass collector happier is designed to exhaust air beside the chute. This allows the hopper to fill completely without decreasing performance. Grass will fall through the opening in the front of the hopper when hopper is full. immediately disengage the power take off and empty the hopper, 7. Cut grass often, especially when turf growth is rapid, if shorter turf is desired, cut the grass again, Overlap the swaths to produce an even cutting pattern.
MAINTENANCE LUBRICATION After Avery 25 hours of operation grease cylinder and privet points with No. 2 multi-purpose lithium base grease. There are (8) grease fittings at various pivot points and (1) fitting on each end of cylinder {Fig. 1B).
A ONE YEAR LIMITED WARRANTY O THAN TRIMMERS The Core Promise N COMMERCIAL PRODUCTS OTHER ND BLOWERS. The Tore Compare promises 1o repair your TOR Product if defective in materials or workmanship. The following time periods from the date of purchase apply Commercial Products Year The costs of parts and labor are included, but the customer pas the transportation Costs on walk rotary mowers. trimmers and blowers.
